Справочник Пользователя для Ingersoll-Rand 666023

OPERATOR’S MANUAL

66602X–X

RELEASED: 6–10–93

REVISED: 6–21–10

(REV.H) IPP/PSE

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1/4” DIAPHRAGM PUMP

1:1 RATIO (NON–METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

GENERAL DESCRIPTION

THIS MANUAL COVERS THE FOLLOWING MODELS

MODEL

TH'D

CHECK TYPE

WETTED MATERIAL

666023,J,H,L*-XXX

NPT

FLAT

POLYPROPYLENE

666026,M,N,P*-XXX

NPT

FLAT

GROUNDABLE ACETAL

* J,H,L,M,N,P Represent Inlet and Outlet Options, refer to page 3 for more information.

SERVICE KITS

Refer to Service Kit Chart on page 3 to match pump material with SerĆ

vice Kits offered. The ``X'' represents a variable digit of the Model No.

637273-XXX for Pump Rebuild. (Model digits 7,8,9)

637274-XX for Check Valve Replacement. (Model digits 7,9)

637275-XX for Diaphragm and Air Section repair. (Model digits 8,9)

637276 for Pre-assembled Replacement Air Valve Section. (Fig.2)

PUMP DATA

MODELS - See Model Description Chart for ``-XXX'' on page 3.

PUMP TYPE -Non-Metallic Air Operated Double Diaphragm

MATERIAL - See Model Description Chart on page 3.

WEIGHT LBS. - Polypropylene 3.6 (1.63 kgs)

- Groundable Acetal 4.1 (1.86 kgs)

MAXIMUM AIR INLET PRESSURE - 100 p.s.i.g. (6.9 bar)

MINIMUM AIR INLET PRESSURE - 20 p.s.i.g. (1.4 bar)

MAXIMUM OUTLET PRESSURE - 100 p.s.i.g. (6.9 bar)

MAXIMUM FLOW RATE - 5 g.p.m. (18.9 Liters)

MAXIMUM SUCTION LIFT - 20 Ft. (Water)

MAXIMUM OUTPUT PER CYCLE -.014 Gallons (53 cc's)

MAXIMUM PARTICLE SIZE - 1/32" dia.

MAXIMUM TEMP. LIMITS -

Polypropylene 35_F to 120_F

Groundable Acetal 10_F to 150_F

GROUNDABLE - 666026-XXX Models Only

DIMENSIONAL DATA - See page 8.

NOISE LEVEL*- 59.8 db(A) @ 70 psi, 60 cycles per minute.

The pump sound pressure levels published here have been updated to an Equivalent Continuous Sound Level (L

Aeq

) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

The ARO Diaphragm Pump offers high volume delivery even at low air

pressures, easy self priming, the ability to pump various viscosity maĆ

terials and the ability to pass solids (as stated in the chart above). The

pump is designed to correspond to the needs of the user by offering a

variety of wetted parts configurations to handle almost any application.

Refer to the model and option chart on page 3.

Model 666026-XXX: The Acetal material used in this pump contains

Stainless Steel fibers, it's conductivity allows it to be connected to a

suitable ground, a ground screw is provided for this.

NOTICE: All possible options are shown in the chart on page 3 however

certain combinations may not be recommended, consult a representative

or the factory if you have questions concerning availability.

666023-XXX

1/4'' DIAPHRAGM PUMP

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 495-0276 FAX(800) 892-6276