Листовка для Ingersoll-Rand 67343

2011

CCN 15207129

(800) 495--0276

FAX (800) 892--6276

INGERSOLL RAND COMPANY

209 NORTH MAIN STREET -- BRYAN, OHIO 43506

www.ingersollrandproducts.com

OPERATOR’S MANUAL

67343

RELEASED:

10-1-03

REVISED:

8-1-11

(REV. 03)

INCLUDING: SERVICE KITS, DISASSEMBLY / REASSEMBLY, PARTS LIST, TROUBLESHOOTING

67343 AIR MOTOR

ALSO COVERS 637399 SERVICE KIT

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

AIR MOTOR DISASSEMBLY

NOTE: All threads are right hand. Carefully remove the parts, inspect for

damage, nicks or excessive wear and determine if any parts will need

replacement.

1. Using a 7/8” wrench, unthread and remove (11) adapter and (12 and

13) “O” rings, releasing (14) muffler housing.

2. Using a 3/8” wrench, unthread (28) tie rods and remove (27) plate.

3. Remove four (1) bolts, (2) upper cap and (3) track gasket.

4. Remove (10) cylinder, containing (4) sleeves and (7) spools.

5. Using (1) bolt, push (7) spools and (4) sleeves out “sleeve” end of

(10) cylinder.

6. Remove (16) retaining ring, (17) washer and (19) piston.

7. Remove (22) dowel pin, releasing (20) piston adapter.

8. Remove (3) track gasket and (23) lower cap.

9. Remove (26) adapter, with (24) “O” ring and (25) “U” cup.

AIR MOTOR REASSEMBLY

NOTE: Thoroughly clean and lubricate all seals. Replace all soft

parts with new ones included in the repair kit.

Note: Refer to the il-

lustration (figure 2, page 2) for “U” cup lip seal direction.

1. Assemble (24) “O” ring and (25) “U” cup to (26) adapter and as-

semble to (23) lower cap.

2. Assemble (29) piston rod up thru (26) adapter.

3. Assemble (3) track gasket to (23) lower cap.

4. Assemble (21) “O” ring to (20) pistonadapter andassemble (20)pis-

ton adapter to (29) piston rod, securing with (22) dowel pin.

5. Replace (18) “U” cups on (19) piston and assemble (19) piston onto

(20) piston adapter, securing with (17) washer and (16) retaining

ring.

6. Replace (5) “O” rings on (4) sleeves and assemble (4) sleeves into

(10) cylinder. NOTE: Assemble each sleeve into the end of the cylin-

der nearest the exhaust hole.

7. Replace (6 and 9) “O” rings and (8) “U” cups on (7) spools and as-

semble (7) spools into (10) cylinder from the opposite end as the (4)

sleeve went in.

8. Assemble (10) cylinder to (23) lower cap, being careful when sliding

over the lips of (18) “U” cups. NOTE: Be sure (3) track gasket is

seated properly.

Figure 1

9. Replace (3) track gasket on (2) upper cap and assemble (2) upper

cap to (10) cylinder.

10. Assemble (1) bolts to air motor.

11. Assemble (27) plate to air motor, securing with (28) tie rods. NOTE:

Tighten tie rods to 80 - 90 in. lbs (9.0 - 10.2 Nm).

12. Replace (12 and 13) “O” rings on (11) adapter.

13. Assemble (15) foam liners to (14) muffler housing.

14. Assemble (14) muffler housing to (10) cylinder, securing with (11)

adapter.NOTE:Torque(11)adapterto80in.lbs(9.0 Nm)maximum.

TROUBLE SHOOTING

If the pump will not cycle or will not deliver material.

•

Be certain to checkfor non-pump problemsincluding kinked,restric-

tive or plugged inlet / outlet hose or dispensing device. Depressurize

the pump system and clean out any obstructions in the inlet / outlet

material lines.

•

Check all seals, including track gaskets.

•

Check the direction of “U” cup lips.