Справочник Пользователя для Sony 530P
Cha
p
te
r 7
Men
u
Dis
pla
y
y
s
and
Det
a
iled Se
tt
ing
s
s
128
7-3 Adjustments and Settings from Menus
To cancel the setting
Before executing step 8, move the
Before executing step 8, move the
b mark to “ESC” at the
top right of the window and press the MENU knob.
Alternatively, push the CANCEL/PRST / ESCAPE switch
down to the ESCAPE side.
All settings or changes are discarded and the TIME/DATE
page of the DIAGNOSIS menu appears.
Alternatively, push the CANCEL/PRST / ESCAPE switch
down to the ESCAPE side.
All settings or changes are discarded and the TIME/DATE
page of the DIAGNOSIS menu appears.
7-3-7 Selecting the Lens File
The LENS FILE page of the USER menu allows you to
change the lens file according to the lens in use.
change the lens file according to the lens in use.
Note
When using a serial lens, lens file selection is not possible.
Proceed as follows.
1
Set the MENU ON/OFF switch to ON.
The last accessed menu page appears on the screen.
2
Turn the MENU knob until the LENS FILE page
appears, then press the MENU knob to select the page.
appears, then press the MENU knob to select the page.
The LENS FILE page shows the name and the f-stop
(iris setting) of the lens currently selected.
(iris setting) of the lens currently selected.
3
Turn the MENU knob to move the
b mark to LENS
FILE SELECT, and press the MENU knob.
The
b mark on the left of the selected item changes to
a z mark and the z mark on the left of the setting
changes to a ? mark.
changes to a ? mark.
4
Turn the MENU knob until the lens file No. in use
appears, then press the MENU knob.
appears, then press the MENU knob.
The z mark changes to a
b mark and the ? mark
changes to a z mark.
If you do not want to use a lens file
Select NO OFFSET.
Select NO OFFSET.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
switch to OFF or close the cover of the menu operating
section.
7-3-8 Selecting the Aspect Ratio
The FORMAT page of the OPERATION menu allows you
to select the aspect ratio of the video output signal.
to select the aspect ratio of the video output signal.
Note
When the CA-701/702/702P camera adaptor is used with
the camcorder, this function is not available. To select the
aspect ratio, disconnect the CA-701/702/702P camera
adaptor from the camcorder or turn off the power of the
CA-701/702/702P camera adaptor.
the camcorder, this function is not available. To select the
aspect ratio, disconnect the CA-701/702/702P camera
adaptor from the camcorder or turn off the power of the
CA-701/702/702P camera adaptor.
Proceed as follows.
1
Follow the procedure of steps 1 to 3 described in
7-3-4 “Specifying an Offset for the Auto White
Balance Setting” on page 124 to display the
FORMAT page of the OPERATION menu.
7-3-4 “Specifying an Offset for the Auto White
Balance Setting” on page 124 to display the
FORMAT page of the OPERATION menu.
2
Turn the MENU knob to move the
b mark to “16:9/4:3
SELECT”, and press MENU knob.
The
b mark on the left of the selected item changes to
a z mark and the z mark on the left of the setting
changes to a ? mark.
changes to a ? mark.
3
Turn the MENU knob to display the desired aspect
ratio, and press the MENU knob.
ratio, and press the MENU knob.
The z mark changes to a
b mark and the ? mark
changes to a z mark.
4
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
switch to OFF or close the cover of the menu operating
section.
To display the aspect ratio of 16:9/4:3 on the
viewfinder screen
By setting the “DISP 16:9/4:3 ID” item on the VF DISP 2
page of the USER menu to “ON”, “16:9” or “4:3” appears
on the viewfinder screen when the aspect ratio of 16:9 is
selected.
viewfinder screen
By setting the “DISP 16:9/4:3 ID” item on the VF DISP 2
page of the USER menu to “ON”, “16:9” or “4:3” appears
on the viewfinder screen when the aspect ratio of 16:9 is
selected.
U15 LENS FILE
LENS FILE SELECT: 1
F.ID :
TOP
20 FORMAT
16:9/4:3 SELECT : 16:9
SCAN MODE : I
UC/J SELECT : UC