Справочник Пользователя для Mitsubishi Electronics 148 Series

For devices operating independently of 
NetCommand:  The F1–F4 keys work like the  A, 
B, C, D buttons on some cable boxes, satellite 
receivers, and DVD players.  Program the remote 
control for your equipment and test the keys.  See 

Appendix C, “Programming the Remote Control.”

  (PAUSE):  Freezes a broadcast TV picture from an 

antenna source, cable box, or satellite receiver (if 
key has not been reassigned for NetCommand use).

Use any of these methods to enable the recording and 
playback commands of the TV’s remote control:

•  Program the remote control for your DVR, VCR, or

DVD player/recorder and set the slide switch to 

VCR, 

DVD, CABLE/SAT, or AUDIO as appropriate.

•  Check HDMI devices for compatibility with the TV’s

NetCommand for HDMI feature (see Appendix E).

•  Perform NetCommand IR “learning” for the device.

  (RECORD):  Records with a VCR or DVR.

  (PAUSE):  Pauses a VCR, DVR, or DVD.  See 

above for use during TV viewing.

  (STOP):  Stops play of a VCR, DVR, or DVD.

  (REVERSE):  Rewinds a VCR.  Reverse scans a 

DVR or DVD.

  (PLAY):  Plays a VCR, DVR, or DVD.

  (FORWARD):  Fast forwards a VCR.  Forward scans 

a DVR or DVD.

Note:  To operate other audio/video devices using 

the TV’s remote control:

•  See Appendix C, “Programming the Remote 

Control.”

•  For HDMI devices compatible with the TV’s Net-

Command for HDMI feature, see Appendix E.

•  See chapter 6, “NetCommand IR Control,” for

NetCommand IR “Learning” of device keys.

•  For use of specific keys with NetCommand-con-

trolled devices, see “Special Operation Methods,” 
page 58.

Use only alkaline batteries.

•

Be within 20 feet of the equipment.

•

Do not press two or more buttons at the same time 

•

unless instructed to do so.
Do not allow unit to get wet or become heated.

•

Avoid dropping on hard surfaces.

•

Do not use harsh chemicals to clean.  Use only a 

•

soft, lightly moistened cloth.
Do not mix old and new batteries.

•

If the slide switch is set to 

TV and the TV does not 

respond properly, reset the remote control.

Press and hold 

POWER for several seconds until the 

button blinks twice and goes off.
Release the 

POWER button.

Press keys 

0   0   9   3   5 and the POWER button will blink 

twice when you finish entering the code.  While 
entering the code, pause for a moment between 
each key press to ensure it is recognized.

If you press a key and the 

POWER key blinks five times, 

replace the remote control’s batteries.

ChannelView™ displays channel names and program 
information, as sent by broadcasters or your local cable 
service provider, for memorized channels on 

ANT 1 or ANT 

2.  Listings may be incomplete.  No program information is 
displayed for analog channels.  An analog channel name is 
displayed only if you assigned a name in the 

Setup > Edit 

menu (page 45).
To receive ChannelView updates:

Keep the Energy Mode set to 

•

Set the TV clock

•

Leave the TV powered off for a while each day to 

•

receive updates.

Listings are updated for the digital channel you are 

 

-

currently watching.
If the time or date displayed are incorrect, change 

 

-

the TV’s time, time zone, date, or Daylight Savings 
Time settings in the 

Setup menu.

See ChannelView listings 
from 

ANT 1 or ANT 2.

Press 

Close ChannelView

Press 

GUIDE or EXIT.

Scan channels one by one. Press and hold   or  .
Scan channels quickly.

Press and hold 

PAGE   /  .

Jump to listings for a 
specific channel.

1.  Enter the channel 

number (see numbers  in 
upper left of screen).

2.  Press 

ENTER.

See more of the program 
description (if available).

Press 

INFO.

Move navigation to the 
program listings.

Press  .

Move navigation to the 
channel listings.

Press  .

Tune to the highlighted 
channel.

Press 

ENTER.