Инструкции для Moeller Marine XControl PLC System AWB2700-1428GB

Содержание

• Title

  1
• Safety instructions

  2
• Contents

  3
• About This Manual

  5
  • Structure

    5
  • Abbreviations and symbols

    5
• 1 Hardware and Engineering

  7
  • Setup

    7
  • Mounting

    8
    • Fitting/removing modules

      8
    • Fitting XI/ON base modules

      10
  • Engineering

    10
    • Control cabinet design

      10
    • Ventilation

      11
    • Device arrangement

      11
    • Preventing interference

      11
      • Cabling and wiring

        11
    • Suppression of interference sources

      11
    • Shielding

      11
    • Lightning protection measures

      11
      • External lightning protection

        11
      • Internal lightning protection

        11
  • Wiring example (overview)

    12
  • Switching the power supply on/off

    12
  • XC-ADP/XC-ADP-XION base modules

    13
    • General

      13
    • Task of the XC-ADP-XION module

      13
    • Task of the XC-ADP module

      13
    • Engineering the XC-ADP-XION base module

      13
      • Power supply for the XI/ON modules

        13
      • Connections

        13
    • Expansion with XI/ON modules

      14
  • XC-POW50-UPS/XC-POW50-XION-UPS power supply modules

    14
    • General

      14
    • Task

      14
    • Setup

      14
    • Engineering

      14
  • XC-NET-DP-M PROFIBUS-DP module

    14
    • General

      14
    • Task

      14
    • Engineering

      15
      • PROFIBUS-DP interface

        15
      • Power supply

        15
      • Start/Stop behaviour

        15
      • Configuring the module address

        15
        • Setting the address on the device

          15
        • Setting the address in XSoft

          15
    • Bus terminating resistors

      16
  • XC-NET-CAN CANopen module

    16
    • General

      16
    • Task of the module

      16
    • Engineering

      16
      • CANopen interface

        16
      • Pin assignment

        16
      • Power supply

        16
      • Start/Stop behaviour

        16
      • Configuring the module address

        16
      • Bus terminating resistors

        17
  • XC-SYS1 operator module

    18
    • Task

      18
    • Setup

      18
      • Operating mode selector switch (OMS)

        18
      • Menu selector switch (MSS)

        19
      • Battery

        19
      • LEDs

        19
      • CompactFlash card

        19
  • XC-CPU601-E.M processor

    19
    • Task

      19
    • Setup

      19
• 2 Establishing the Connection Between PC and XC600

  21
  • Requirements of the Ethernet module in the PC

    21
  • Configuring the Ethernet module

    21
    • Specifying the IP address

      21
  • Configuring the XC600

    22
  • Creating the connection between PC and XC600

    22
    • Hardware

      22
    • Software

      22
• 3 Creating an Example Project

  25
  • Setting the target system

    26
  • Configuring the XC600 controller

    27
    • Creating programs

      29
      • Task

        29
      • Procedure

        29
  • PROFIBUS-DP expansion

    30
    • Adding a PROFIBUS-DP module to the XC600 controller

      30
    • Adding a remote XI/ON gateway

      30
    • Creating a program for PROFIBUS-DP expansion

      31
  • CANopen bus expansion

    32
    • Adding a CANopenmodule to the XC600 controller

      32
    • Creating a program for remote outputs on the CANopen bus

      34
• 4 Functions of the Operator Module

  35
  • Initial PLC startup

    35
  • Loading the program into the PLC

    35
  • Starting up the PLC with a bootable and activated program

    36
  • Entering parameters or status modifications

    36
    • Without a password

      36
    • With password

      36
  • Starting programs

    37
    • In the Online menu of XSoft via Start

      37
    • Using the OMS of the operator module

      37
  • Display programs on the hard disk (internal) and on the CompactFlash card (external)

    37
  • Startup with configuration scan

    38
  • Error and event messages

    38
    • Error messages

      38
    • Event message

      38
  • General messages

    39
    • Deleting programs from the hard disk

      39
  • Deleting programs from the working memory

    39
    • Reset function (initialisation of variables)

      39
      • Executing Reset via XSoft

        39
      • Executing RESET on the operator module

        39
      • Executing the MRES function on the OMS

        39
  • Handling several programs

    40
  • Deleting programs

    40
  • Copying programs

    40
  • Editing programs on the CompactFlash card (CFC)

    40
  • Password

    41
    • Entering passwords

      41
    • Accepting and activating passwords

      41
  • Displaying text from the user program

    41
    • Shutting down the system

      42
  • Switching off the power supply

    42
• 5 Menu Overview of the Operator Module

  43
  • Basic menu

    44
    • DISPLAY menu

      44
    • MAIN MENU

      44
      • MAIN MENU: DIAGNOSTICS

        44
        • EVENT

          44
        • ERROR

          44
        • CLEAR

          44
      • MAIN MENU: PROGRAM

        45
        • RESET

          45
        • INTERNAL/EXTERNAL

          45
        • LOAD

          45
      • MAIN MENU: RECIPE

        46
        • EXTERNAL/INTERNAL

          46
      • MAIN MENU: DEVICE

        46
        • NETWORK

          46
        • DATE/TIME

          46
        • SECURITY

          46
        • LANGUAGE

          47
        • SOFTWARE

          47
        • HARDWARE

          48
      • MAIN MENU: SYSTEM

        48
• Appendix

  49
  • Other error messages

    49
  • Technical Data

    50
• Index

  53