Справочник ПользователяСодержаниеNOTICE FOR CUSTOMERS IN THE UNITED KINGDOM2A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.2Should the fuse in the plug supplied need to be replaced, a 10 AMP fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used.2When an alternative type of plug is used it should be fitted with a 10 AMP FUSE otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board.2If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse...2Open the fuse compartment with a blade screwdriver, and replace the fuse. Please refer to the illustration that actually equipped with the product.2Start-up Guide4Before Use4To check the accessories4To insert batteries into the remote41: Attaching the stand41 Open the carton box and take out the stand and the screws.42 Place the TV set on the stand. Take care not to interfere with cables.43 Fix the TV to the stand according to the arrow marks that guide the screw holes using the supplied screws.4~42: Connecting an aerial/Set Top Box/recorder (e.g. DVD recorder)53: Preventing the TV from toppling over51 Install a wood screw (4 mm in diameter, not supplied) in the TV stand.62 Install a machine screw (M4 ° 20, not supplied) into the screw hole of the TV.63 Tie the wood screw and the machine screw with a strong cord.64: Bundling the cables6~65: Performing the initial Set-up6~6Adjusting the viewing angle of the TV7Adjust the angle left and right (swivel)7Detaching the Table-Top Stand from the TV7~7Safety Information8Precautions9Remote and TV Controls/Indicators10Remote and TV controls10z10~10~11z11~12Indicators13About the operation guide on the TV screen13Watching TV14Watching TV141 Press 1 on the TV to turn on the TV.142 Press DIGITAL to switch to digital or satellite mode, or press ANALOG to switch to analogue mode.143 Press the number buttons or PROG +/- to select a TV channel.14To access Digital Text14To access Analogue Text15z15To change the Screen Format manually15~15z15~15Instruction Manual16Instruction Manual16Navigating through the Instruction Manual161 Press HOME to display the XMB™.162 Press G/g to select Settings.163 Press F/f to select Instruction Manual, then press .164 Press F/f to select topic from the Table of Contents, then press . Use the corresponding coloured button to go to next or prev...165 Press HOME to exit.16~16How the switchover affects your TV equipment:27How to re-tune:281 Press "HOME" on the remote282 Press G/g to select "Settings"283 Press F/f to select "Digital Set-up", then press284 Press to select "Digital Auto Tuning"285 Press G to select "Yes" then press to start "Digital Auto Tuning"286 Follow the on screen instructions.28Additional Information17Installing the Accessories (Wall-Mount Bracket)17To Customers:17To Sony Dealers and Contractors:17~17TV installation dimensions table18Figures in the above table may differ slightly depending on the installation.18The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to “Specifications” (page 20) for its weight.18Screw and Hook locations diagram/table19Specifications20* 1080p timing when applied to the HDMI input will be treated as a video timing and not a PC timing. This affects the “Video Settings” menu and “Screen” menu settings. To view PC contents, set “Screen Format” to “Wide” and “Display Area” to “Full Pixel”.22~22Troubleshooting231 Count how many times the 1 (standby) indicator flashes between each two second break.232 Press 1 on the TV to turn it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (number of flashes).231 Check the items in the tables below.232 If the problem persists, have your TV serviced by qualified service personnel.23Размер: 3,9 МБСтраницы: 28Язык: EnglishПросмотреть
