RCA RCR6373 用户手册

2

Your universal remote can operate a variety of brands of 
components. In order for your universal remote to control your 
components, you need to program the remote with the codes 
that match the components (see Code Lists enclosed or go to 
rca.com/codefinder). These codes enable the remote to 
communicate with your components. Each brand and each 
component has its own “language,” and, by programming the 
correct codes into your remote, you tell the remote to “speak the 
same language” as your components.

Most components can be programmed in one of these four 
ways. Try them in the order listed.

In order to control combo TV/VCR or TV/DVD units, you 
must program both the TV key and the DVD or VCR•AUX2 
key. Once programmed successfully, the TV key controls the 
TV functions on your unit, and the DVD or VCR•AUX2 key 
controls the DVD or VCR functions. There is a specific section 
in the Code Lists for combo units. The codes in this section 
should be tried first, using Direct Code Entry on the TV and 
DVD or VCR•AUX2 keys. If this is unsuccessful, follow the 
normal programming methods for both the TV and the DVD 
or VCR•AUX2 keys.

The DVR•AUX1 key defaults to program a DVR. If you want 
the DVR•AUX1 key to control a component other than a DVR 
(an additional TV or DVD, for example), you must preprogram 
the DVR•AUX1 key. See the section entitled “Programming 
the DVR•AUX1 and VCR•AUX2 Keys To Control Other 
Components” on page 3.

The VCR•AUX2 key defaults to program a VCR. If you want 
the VCR•AUX2 key to control a component other than a VCR, 
you must  preprogram the VCR•AUX2 key. See the section 
entitled “Programming the DVR•AUX1 and VCR•AUX2 Keys 
To Control Other Components” on page 3.

The online interactive code finder at www.rca.com/codefinder makes it 
easier to find exactly the right codes for your components. The code finder 
takes you right to the best code(s) for your component—no need to go 
through long code lists!

If your brand is listed in the Brand Code List (See Code 
Lists enclosed), you may be able to program your universal 
remote by searching through only the codes for that specific 
manufacturer. Brand Code Search and Entry can be the 
quickest method to program your remote, if your component is 
one of those brands listed.

If your brand is not listed in the Brand Code List, use one of 
the other programming methods that follow.

Follow these instructions to program your remote using the 
Brand Code Search and Entry method.

TIP: To exit without saving at any point in the Brand 
Code Search, press the CLEAR key.

1.  Manually turn on the component you want the remote to 

control (TV, VCR, DVD, DVR, satellite receiver, cable box, 
or audio component).

2.  Locate the Brand Codes in the Code Lists and keep it handy.

Note: If you press an invalid key during the Brand Code Search, 
the remote does not respond. If you do not press a valid Brand 
Code Search key (TV, SAT•CBL, DVD, DVR•AUX1, AUDIO, 
VCR•AUX2, POWER, CLEAR, and number keys 0-9), the search 
times out after two minutes. When the search times out, the LED 
blinks four times and turns off. The last programmed code under that 
component key is retained.

3.  Press and hold the component key 

(TV, SAT•CBL, DVD, DVR•AUX1, 
AUDIO, VCR•AUX2) you wish to 
program. The LED turns on and 
remains on. Keep holding down 
the component key.

4.  While holding the component key down, press and hold the 

POWER key. The LED turns off. After holding both keys 
down for three seconds, the LED turns back on.

5.  Release both keys. The LED remains on.

6.  Refer to the Brand Codes in the enclosed Code Lists. Use 

the number keys to enter the number for your brand. The 
LED blinks once.

TIP: Throughout the programming of each key, be sure to keep the 
remote pointed at the IR sensor of the component you are currently 
programming the remote to control.

7.  Press the POWER key repeatedly until your component 

turns off. Each time you press the POWER key, the LED 
blinks and the next code is sent. The Brand Code Search 
begins with the first code in the chosen brand list for that 
component and cycles through all the codes for that brand. 

  If your component turns off, you have found the correct 

code. 

8.  Once you have found the correct code, press the 

STOP key to save it. The LED turns off.

Notes:  
• To program the DVR•AUX1 key to control a component other 
than a DVR, see page 3.  
• To program the VCR•AUX2 key to control a component other 
than a VCR, see page 3.

IMPORTANT: You must press the STOP key to save the code or the 
correct code will not be stored!