Regency Wraps P36-LPG4 用户手册

Regency

®

 P36-4 Gas Log Fireplace

1)  Locate appliance
 a) 

Locate 

Your 

Gas 

Fireplace

 b) 

Clearances

 c) 

Combustible 

Mantels

 d) 

Framing 

& 

Finishing

2)  Assemble Top Standoffs and Top Facing 

Support and Side Nailing Strips, refer to 
section "Unit Assembly Prior to Installation". 
(NOTE: must be done before installing unit 
into fi replace.)

3)  Install fl ue (Refer to section "Simpson Dura-

vent Flueing").

4)  Make gas and electrical connections. Test 

the pilot. Must be as per diagram. Refer to 
section "Pilot Adjustment."

5)  Install standard and optional features.  Refer 

to the following sections:

 
 a. 

Brick 

Panels

 

b. Log Set

 c. 

Flush 

Door

 d. 

Premium 

Flush 

Front

 e. 

Bay 

Door

 f. 

 

Hampton

®

 Cast Faceplate

 g. 

Hampton

®

 Cast Grills

 h. 

Wall 

Switch

 

i.  Remote Control

 j. 

 

Wall 

Thermostat

 k. 

Fan

6) Final 

check.

Before leaving this unit with the customer, 
the installer must ensure that the appliance is 
fi ring correctly and operation fully explained 
to customer.

1)  Clocking the appliance to ensure the correct 

fi ring rate (rate noted on label 30,000 Btu/h) 
after burning appliance for 15 minutes.

2)  If required, adjusting the primary air to ensure 

that the fl ame does not carbon. First allow 
the unit to burn for 15-20 min. to stabilize.

The P36-NG or P36-LPG Room Sealed Fireplace 
must be installed in accordance with AS5601-
2004 and NZS 5261 5261 and these instructions. 
Carefully read all the instructions in this manual 
fi rst. Consult the "authority having jurisdiction" 
to determine the need for a permit prior to 
starting the installation. It is the responsibility of 
the installer to ensure this fi replace is installed 
in compliance with manufacturer's instructions 
and all applicable codes.

1)  The appliance shall be installed in 

accordance with the manufacturer's 
installation instructions,local gas fi tting 
regulations, municipal building codes, 
water supply regulations, electrical wiring 
regulations, with AS5601-2004 (AGA 
gas installation code) NZS 5261 (New 
Zealand)

2)  Installation and repair should be done 

3)  THIS APPLIANCE IS NOT INTENDED AS A 

4)  This appliance must be connected to 

5)  Inspect the fl ueing system annually for 

blockage and any signs of deterioration.   

6)  Flueing terminals shall not be recessed into 

a wall or siding.

7)  Any safety glass removed for servicing 

must be replaced prior to operating the 
appliance.

8)  To prevent injury, do not allow anyone who 

is unfamiliar with the operation to use the 
fi replace.

9)  Wear gloves and safety glasses for protection 

while doing required maintenance.

10) Be aware of electrical wiring locations in 

walls and ceilings when cutting holes for 
termination.

11) Under no circumstances should this 

appliance be modifi ed. Parts that have to be 
removed for servicing should be replaced 
prior to operating this appliance.

12)  Installation and any repairs to this appliance 

should be done by an authorised service 
person. An authorised service person should 
be called to inspect this appliance annually. 
Make it a practice to have all of your gas 
appliances checked annually.

13) Do not slam shut or strike the glass door.

14) Under no circumstances should any solid 

fuels (wood, paper, cardboard, coal, etc.) 
be used in this appliance.

15) The appliance area must be kept clear and 

free of combustible materials, (gases and 
other fl ammable vapours and liquids).