Regency Wraps F2400M 用户手册

Regency Freestanding Woodstove

16

Slide the tube into the left hand side, as far 
as possible and then bring it back into the 
hole on the right hand side until it locks into 
position.  If the tube will not slide in easily, 
simply use a pair of vise grips or pliers and 
tap it into place with a hammer.  A tighter fi t 
will ensure the tube will not move when the 
unit is burning.

2)  Slide the left baffl e over the air tubes from 

the front and then push it to the  back. 

1 6DVL8693  Connector 

Kit

1  6DP-MH9096 Mobile Home Kit

1  6CL48  

48" Chimney length (also in  

 

 

12", 18", 24" lengths.

1 6RC 

 

Rain 

Cap

1  6RCS 

Spark Screen (for rain cap)

1  6RDS/SQS  Round/Square support box
1 6VF 

Flashing

1 6UBA 

"Ultrablack" 

Close 

Clearance

  

Connector

*The use of alternate pitch fl ashings, support 
box extensions, additional chimney lengths, 
and additional chimney bracing, may be used 
on each of the previously listed systems.  These 
parts though must be from the same system 
as listed, and must be a similar and/or compli-
mentary part.

The fl ue baffl e system located in the upper area 
of the fi rebox is removable to make cleaning 
your chimney system easier.  The baffl es must 
be installed prior to your fi rst  fi re.  Smoke 
spillage and draft problems may occur if 

the baffl es are improperly positioned.  Check 
the position of the baffl es on a regular basis as 
they can be dislodged if too much fuel is forced 
into the fi rebox.

The unit arrives with the  2 baffl es on the fl oor 
of the fi rebox. 

1)  If all 4 air tubes are installed continue on to 

Step 2), if not, follow the instructions below. 
Install the air tube into the holes in the side 
channels. The notch goes on the right hand 
side with the air holes facing toward the door. 

The Regency F2400M and S2400M  Freestand-
ing pedestal units are approved for installation 
in a Mobile Home if one of the following pipe 
systems is used. 

1 6DS-VK  Connector 

Kit

1 6TMH 

Shield/Support

1 6TAF-6 

Flashing

1 6T-36 

Chimney 

Length

1 6T-18 

Chimney 

Length

1 6T-CT 

Rain 

Cap 

1 PV06-TK  Connector
1 CSB 

Shield/Support

1 RRS 

Radiation 

Shield

1 LFR03 

Flashing

1 SL3 

Chimney 

Length

1 SL1 

Chimney 

Length

1 RCSA 

Rain 

Cap

1 DL42A-6  Connector 

Kit

1 6SS 

Shield/Support

1 6FAMH 

Flashing

1 6L3 

Chimney 

Length

1 6L1 

Chimney 

Length

1 CPE 

Rain 

Cap

1 DL42A-6  Connector 

Kit

1 6XSF 

Support

1 6XFA 

Flashing

1 6XL3 

Chimney 

Length

1 6XL18 

Chimney 

Length

1 6XCPE 

Rain 

Cap

1 6DWBK 

Connector

1 6TGRS 

Roof 

Support

1 6TGG36  Chimney 

Length

1 6TGG12  Chimney 

Length

1 6TGF 

Flashing

1 6TGC 

Rain 

Cap

1 6DCC 

Connector

1 6HSRS-12 Roof 

Support 

  

(6PLRS-12-BK)

1 6F 

Flashing

1 6HS-36 

Chimney 

Length

1 6HS-18 

Chimney 

Length

1 6HS-RCS  Rain 

Cap 

(6PL-MPC)

3)  Tilt the left baffl e up on top of the side chan-

nel and it will leave enough room to position 
the right baffl e  in the same manner as Step 
1) above. Then reposition the left baffl e fl at 
on the air tubes.