Hifionics BRE2500.1D 用户手册
POWER INPUT
GND REM BA
TT+12V
SPEAKER OUTPUT
RIGHT LEFT
- + - +
BRIDGED
FUSE
HP
FULL
FULL
LP/BP
10Hz 15KHz
30Hz 150Hz
0dB 10dB
6V 0.2V
REMOTE
HI P
ASS
LOW P
ASS
BASS EQ
LEVEL
POWER
X-OVER
PROTECT
LINE INPUT
L
R
L
R
LINE OUT
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY +12v
VIA FUSE
VIA FUSE
MONO SPEAKER
or SUBWOOFER
POWER INPUT
GND REM BA
TT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT
RIGHT LEFT
- + - + - + - +
BRIDGED
BRIDGED
FUSE
LINE INPUT
REMOTE
POWER
PROTECT
LINE OUT
HI FULL
LP/BP
HI FULL
LP/BP
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
HI P
ASS
LOW P
ASS
BASS EQ
LEVEL
X-OVER
1
/2 CH
6V 0.2V
10Hz-15KHz
30Hz-150Hz
0dB-10dB
X-OVER 3
/4 CH
HI P
ASS
LOW P
ASS
BASS EQ
LEVEL
MODE
CH2-CH4
L
R
L
R
L
R
CH1/2
CH3/4
BRE60.4 / BRE100.4 4-CHANNEL AMPLIFIER APPLICATIONS
5
Front/Rear high pass, using a 2 channel amplifier for mono sub bass
Channels 1/2:
The combination of a 2 and a 4 channel amplifier, utilizing their built in
- HI PASS: 100 Hz
crossovers, makes it a snap to put together a full system with front and rear
highs, with mono sub bass.
highs, with mono sub bass.
LOW PASS: N/A
Interconnect cable checklist:
Channels 3/4:
- Using good quality RCA cables, feed the front and rear outputs of a head unit to
- HI PASS: 100 Hz
the inputs of the 4 channel amplifier as shown.
- LOW PASS: N/A
- Also connect the LINE OUT of the 4 channel amplifier to the LINE INPUT of the
2 channel amplifier as shown.
2 channel amplifier as shown.
2 channel bass amplifier:
- HI PASS (Subsonic filter): 10 Hz to 40 Hz
- HI PASS (Subsonic filter): 10 Hz to 40 Hz
Mono bass woofer wiring:
- LOW PASS: 80 Hz
Connect the mono speaker positive terminal to the LEFT +, and its negative
terminal to RIGHT -.
terminal to RIGHT -.
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section “Setting up systems
loudspeaker manufacturer specifications and the section “Setting up systems
Switch setting checklist:
after installation for best performance”
4 channel highs amplifier:
- 1/2CH X-OVER: HI
- 1/2CH X-OVER: HI
Level control checklist:
- 3/4CH X-OVER: HI
- Refer to the section “Setting up systems after installation for best performance”
2 channel bass amplifier:
Minimum final loudspeaker impedances:
- X-OVER switch: LP/BP
- 2 ohm per channel in stereo mode.
- 4 ohm mono bridged.
- 4 ohm mono bridged.
Crossover frequency control checklist:
- 4 channel highs amplifier:
- 4 channel highs amplifier:
STEREO
INTERCONNECT
RCA CABLE
BRUTUS
BRUTUS
ELITE
ELITE