Philips FW-P900 用户手册
21
English
3139 115 20411
CD Operation
Discs Playback
To playback all discs on the disc tray
● Press PLAYÉÅ.
➜ All the available discs will playback once and
then stop.
➜ During playback, the selected disc tray, track
number and elapsed playing time of the current
track will appear on the display.
then stop.
➜ During playback, the selected disc tray, track
number and elapsed playing time of the current
track will appear on the display.
To playback one disc only
● Press the DISC DIRECT PLAY button : DISC 1,
DISC 2 or DISC 3.
➜ The selected disc will playback once and then
stop.
stop.
To interrupt playback
● Press PAUSEÉÅ.
● To resume playback, press PLAYÉÅ again.
To stop playback
● Press Ç.
To search for a particular passage during
playback
playback
● Press and hold à or á and release it when
the desired passage is located.
➜ During searching, the volume will be reduced.
➜ During searching, the volume will be reduced.
To select a desired track
● Press í or ë repeatedly (or Digits 0–9 on
the remote control) until the desired track
appears on the display.
appears on the display.
● If in the stop position, press PLAYÉÅ to start
playback.
Note:
– If in Shuffle mode, pressingí will cause the
player skip only to the beginning of the current
track.
– If in Shuffle mode, pressingí will cause the
player skip only to the beginning of the current
track.
To skip to the beginning of the current
track during playback
track during playback
● Press í once.
Replace discs during playback
1
Press DISC CHANGE.
2
To change the inner disc, press DISC
CHANGE again.
CHANGE again.
➜ "DISC CHANGE" will be displayed and the
disc will stop playing.
➜ The disc tray will close to retrieve the inner
disc and then open again with the inner disc
accessible.
disc will stop playing.
➜ The disc tray will close to retrieve the inner
disc and then open again with the inner disc
accessible.
Programming the disc tracks
Programming tracks is possible when playback is
stopped. Up to 40 tracks can be stored in the
memory in any order.
stopped. Up to 40 tracks can be stored in the
memory in any order.
1
Load the desired discs on the disc tray (refer to
“Loading Discs”).
“Loading Discs”).
2
Press PROG to start programming.
➜
PROGRAM
will start flashing.
3
Press CD (CD 1•2•3) or DISC 1/2/3 button
to select a disc.
to select a disc.
4
Press í or ë (or Digits 0–9 on the remote
control) to select the desired track.
control) to select the desired track.
5
Press PROG to store the track.
● Repeat steps 3–5 to store other discs and
tracks.
6
Press PLAYÉÅ to start program playback.
➜ "PLAY PROGRAM" will be displayed.
● To end programming without playback, pressÇ
once .
➜ The total number of tracks programmed and
total playing time will appear on the display.
total playing time will appear on the display.
Notes:
– If the total playing time is more than "
– If the total playing time is more than "
99:59"
or if one of the programmed tracks has a number
greater than 30, then "
greater than 30, then "
--:--" will appear on the
display instead of the total playing time.
– If you attempt to program more than 40 tracks,
"
– If you attempt to program more than 40 tracks,
"
PROGRAM FULL" will be displayed.
– If you press any of the DISC DIRECT PLAY
buttons, the system will playback the selected disc
or track and the stored program will be ignored
temporarily. The
buttons, the system will playback the selected disc
or track and the stored program will be ignored
temporarily. The
PROGRAM
display also will
disappear temporarily from the display. It will
reappear when playback of the selected disc ends.
– During programming, if no button is pressed
within 20 seconds, the system will exit the Program
mode automatically.
reappear when playback of the selected disc ends.
– During programming, if no button is pressed
within 20 seconds, the system will exit the Program
mode automatically.
pg 001-033/P900/37-Eng
12/8/00, 1:53 PM
21