Rocketfish RF-RBWS01 产品宣传页

2  Adjust the antennas 
 

Adjust the antennas to gain the best audio signals. 

 

Tip: In some cases, you may improve range by rotating 
both antennas 0° to create a 180° angle. 

3  Enable the remote control battery
 

Remove the tab from the bottom of 
the remote control.

 The 

Quick Setup Guide will show you a typical 

setup using an audio device (such as an MP3 
player, PC or A/V receiver). For more information 
about how to use other Rocketboost products 
with this product, see your User Guide. 

 

See the following steps for further setup details.

Wireless sender/receiver

AC power adapter

for wireless sender/receiver

Remote control

USB cable

3.5 mm to RCA adapter 

(6 inches/15.25 cm)

Wireless speakers

AC power adapter
for wireless speakers

3.5 mm 
audio cable

The wireless sender/receiver and wireless speakers were pre-joined so they will communicate with 
each other right out of the box. So if this is your first Rocketboost enabled product you can skip 
this section and go to the next section, Listening to music.
If you need to rejoin the wireless sender/receiver to the wireless speakers, and this is your only 
Rocketboost enabled product, then use the following steps. 
1 Set 

the 

HUB STATUS switch on the wireless sender/receiver to ENABLE if this is your first 

Rocketboost product set.

 

•   The power indicator turns green when the HUB STATUS switch is set to ENABLE.

 

•   The power indicator turns blue when the HUB STATUS switch is set to DISABLE.

2  Press and hold       on the wireless sender/receiver for more than three seconds to put it into 

joining mode. The power indicator starts blinking rapidly and the unit will stay in joining mode 
for 30 seconds.

3  Press and hold the       button on the wireless speaker for more than three seconds 

so the wireless sender/receiver and wireless speaker enter connection mode.

 

•   The power indicator lights steadily if the joining was successful.

 

•   The power indicator blinks slowly if the joining was not successful.

4  After the link is established, if the Source indicator on 

the wireless speaker is still not illuminated, make sure 
that your source is turned on.
For more instructions, see your User Guide.

If you already have other Rocketboost devices you need 
to join both the wireless sender/receiver and the wireless 
speaker to your existing hub device. See the User Guide 
for detailed instructions on how to do this.

1  Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should 

light steadily. If they are blinking you need to rejoin the wireless sender/receiver and wireless 
speaker. See the Establishing communication section above.

2  Point the remote control at the wireless sender/receiver and select either USB-In or LINE-In 

depending on which audio input you are using.

3  Play music from the audio device connected to your wireless sender/receiver and listen to it 

from the wireless speakers. 

4  Adjust the volume level on your wireless speaker. If you have multiple audio sources in your 

Rocketboost network, press the Source button on the wireless speaker to hear the next audio 
source. Press the Source button again to cycle through all available audio sources.
Note: Be sure to turn up the volume on your audio source device, especially if you are 
connected to a headphone output.

Every Rocketboost network must contain 
one hub device, which helps devices join 
the network. The network can have only 
one hub, which you can enable using the 
hub switch on the back of all Rocketboost 
wireless sender and wireless 
sender/receivers. If this is your first 
Rocketboost product, you should make 
the wireless sender/receiver the hub, if you 
already have Rocketboost products, you 
should disable hub mode on this device.

Important: Hub devices must always have 
power for your network to operate. The 
hub device can be in standby (power-
saving) mode, but must stay plugged in.

© 2011 BBY Solutions, Inc. All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645

ENGLISH 11-0203

Connect the AC power adapter to the wireless 
speaker and plug into an AC power outlet. The 
wireless speaker system turns on automatically.

1  Connect your audio source to the LINE IN jack or USB jack on the rear of the wireless sender, 

using the 3.5 mm audio cable or the USB cable. If necessary, you can also use the 3.5 mm to RCA 
adapter, if your audio device uses RCA-type line out connectors.

2  Remember to turn the volume up on your audio source especially if connected to a headphone 

output.

3  Connect the AC power adapter to the wireless USB sender/receiver and plug into an AC power 

outlet. 
The wireless sender/receiver automatically turns on and the power indicator turns green.

RF-RBWS01

Wireless
speakers

RF-RBUSB

Wireless

sender/receiver

Right speaker

back

Included 3.5 mm cable

To audio output jack

Included USB cable

To USB jack

Included 3.5 mm cable
and 3.5 mm to RCA adapter

To audio

output jack

standby

SOURCE

Lights when 
speaker is 
receiving 
audio from 
sender

g)

,

y p