Sonic Alert SBR350SS 产品宣传页

 
IMPORTANT- Please read these instructions carefully before use and retain for future 
reference. See operating instructions on back. 
 

Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before 
connecting, make sure that the requirements specified on the apparatus corresponds to the available 
power supply i.e. AC 110V/220-340V (50Hz/60Hz) 
 

Power: Consumption:  8w, 110v / 60 Hz 
Radio Frequency:  U.S. AM: 540-1700 KHz  /  FM: 88-108 MHz 
UL listed transformer (Underwriters Laboratories) 

NSTRUCTIONS 
AM / FM RADIO ALARM CLOCK WITH BED SHAKER  
MODEL SBR350SS 
 

 

1) Setting Switch 

 

7) Minute Button 

 

13) AM / FM Band Switch 

 

2) Dimmer Switch 

 

8) Snooze Button 

 

14) Backup Battery Compartment

 

3) Alarm Indicator 

 

9) Alarm Off Button   

15) AC Power Input   

 

4) PM Indicator 

 

10) Volume Control   

16) Vibrator Input 

 

 

5) Sleep Button 

 

11) Function Switch   

17) FM Antenna 

 

 

6) Hour Button 

 

12) Tuning Dial 

 

18) Alarm option switch

 

1) 

Slide the setting switch (1) to the position marked “TIME”. 

2) 

Depress hour button (6) as necessary to advance the clock display until the hour is correct. 

3) 

Depress minute button (7) as necessary to advance the clock display until the minute is correct. 

4) 

Slide the setting switch (1) to the position marked “LOCK” this will prevent the clock time from 
being changed. 

5) 

Lighted dot (10) in upper left clock display indicates time is PM, no light indicates time is AM. 

 

 

1) 

Simply follow the instructions mentioned under “ Setting the correct time” except that you will 
have to slide switch  (1) to the “AL” position. 

2) 

Make sure the alarm time is correctly set for AM or PM lighted dot (10) indicates PM).  Be sure 
to release the HOUR and MIN set buttons before releasing the ALARM button. 

3) 

Once the alarm time is set slide the setting switch (1) back to the position marked “LOCK” this 
will prevent the alarm from being changed.  

4) 

To enable the alarm function, slide the Function Switch (11) to position marked “ALARM”. 
This will turn on the alarm feature. Otherwise, alarm will not go off for the alarm time set. 

5) 

You will see a dot (3) on the left side of the LED display to show the alarm has been enabled. 

To use battery backup, you can install a 9-volt alkaline battery in the back of the clock located under the 
battery cover (7). Battery not included. Note the LED display will not show during power failure but the 
clock will still be running and keeping proper time until the power comes back.  

1) 

Slide the Function Switch (11) to “ON” position to turn radio “ON”. 

2) 

Use rotary volume wheel (10) and turn to desired listening level. 

3) 

Slide Band Switch (13) to either AM or FM. 

4) 

Tune radio station by turning the Tuning Dial (12) to desired radio frequency. 

For best reception unwind wire antenna cord to its full length (16). Make sure radio isn’t near any 
electrical appliances that may cause interference. 

1) 

You may use the sleep function to have the radio on while you go to sleep. It will automatically 
shut itself off after the specified time. 

2) 

Make sure the Function Switch (11) is NOT set to “ON” otherwise sleep function will not work 
and the radio will play continuously.  

3) 

Press sleep button (5) and radio will play for an hour. You can also set sleep timer for other 
lengths of shut off time. 

4) 

Press and hold the sleep timer button (5). It will start at 59 minutes and countdown to 1 minute. 
Release sleep timer button (5) once the desired sleep time is chosen. 

Set alarm wakeup time by following the procedure under “Setting the Correct Time” Slide the 
function switch (11) to position marked “AUTO”, this will turn on the radio feature at the alarm time 
set.  Otherwise radio will not go off for the alarm time set. 

You may use the sleep function to have radio on while you go to sleep and have the radio wake you in 
the morning. Follow directions under section labeled Sleep Timer Operation and Wake To Radio. 

You may use the sleep function to have the radio on while you go to sleep and have the buzzer wake 
you in the morning. Follow the directions under Setting the Alarm Time and Sleep Timer Operation. 

Alarm can be shut off temporary for the day or permanently shut off.  
1) 

When the alarm goes off, simply press the AL off button (9) the alarm will shut itself off for the 
day and come back on the next day at the same time if alarm setting has not changed 

2) 

To shut the alarm off permanently, slide function switch  (11) to off position. Alarm will not 
come on until Function Switch (11) is set to “AUTO” or “ALARM” position.  

SNOOZE button (13) - press after alarm has sounded.  The alarm will be turned off for 9 minutes for 
extra sleep.  The alarm will come back again after 9 minutes.  You may repeat up to 59 minutes. 

Set the alarm time you wish and slide the VIB / BUZZ / OFF  (12) switch to the desired position. Set 
to VIB for bed shaker and BUZZ for sound, or VIB/BUZZ for both.  

To adjust the volume rotate the wheel located on back right side (5).  

1) 

Attach the bed shaker jack to the back of clock at VIBRATOR input. 

2) 

To turn on vibrator slide switch (12) to VIB or VIB/BUZZ position. 

3) 

Place vibrator under mattress or pillow. 

Attach the AC power supply input to the back of clock at AC-9V IN next to the VIBRATOR input, 
smaller input of the two. Important do not confuse input with vibrator input.