Toshiba TLP-S40 用户手册

33

32

■ The display setting menu

Use this menu to set screen display-related items.

(Full):  Display with LCD panel’s resolution
(Thru): Display with sampling resolution (for computer input)
(Wide):  Wide-screen display (for Video, S-video, and Y/P

B

/P

R

)

Select one of the languages below to use for displaying menus and messages
[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/
Português/            /                      /                      /

Screen to display when there is no input signal                         (Logo)                            (Blue)                            (None)

Display icons as function guides

Display start-up screen when power turned on 

Description

Item

• If “Thru” is selected for screen size, portions exceeding the pixel count of the LCD panel

 will not appear on the screen. Note that for RGB signals with clock speeds

SXGA3_60 

 or lower, all input pixel signals are sampled. (This effect is noticeable

when the screen is enlarged using the Resize function 

). However, if the clock speed

is higher than this, the RGB pixel signal is reduced before sampling.

• Displaying the images with the aspect ratio different from the original with the purpose of

other than the personal and private viewing, using the screen size menu may violate the
copyright protected by the law.

■ Reset menu (Special menu)

When other menus are not displayed and the 

 button is held down, the menu appears.

• When the screen is placed vertically, and Auto keystone correction is executed, but the

keystone correction is not successful, stow the foot adjuster in its original position, place
the projector on a flat surface, select Horizontal reference value reset, and press the 
button.

• Select Reset All and press the 

 button to return all menu items to the factory settings.

Reset the horizontal reference value for Auto keystone correction
[     : Enter execution mode]     [Yes           No]     [Apply:     ]

Reset all menu items to their factory settings
[     : Enter execution mode]     [Yes           No]     [Apply:     ]

Description

Item

■ The image adjustment menu

Use this menu to adjust image-related items.
Items that can be adjusted are marked with  “Yes”, and those that cannot are marked with “No”.

Item    

  

Description

Computer Y/P

B

/P

R

Video S-video Camera

 

Lower

Higher

Yes

Yes

Yes

Yes

Yes

Darker

Brighter

Yes

Yes

Yes

Yes

Yes

Lighter

Deeper

No

Yes

Yes

Yes

No

Reddish

Greenish

No

No

Yes

Yes

No

Softer

Sharper

No

Yes

Yes

Yes

Yes

Less red

More red

Yes

Yes

Yes

Yes

Yes

Less green

More green

Yes

Yes

Yes

Yes

Yes

Less blue

More blue

Yes

Yes

Yes

Yes

Yes

Shift down

Shift up

No

Yes

Yes

Yes

No

Notes
1: Tint can only be adjusted when Video mode 

 is set to NTSC or NTSC4.43.

2: Up/down shift can only be adjusted when Screen size 

 is set Wide.

■ The default setting menu

This menu shows placement status and other settings.

Sets the period of time to wait until turning off the power after signal input stops: 
Off (not turned off)          1 min           2 min           ...          60 min

Sets whether to turn on the power when the ON/STANDBY button is pressed 
(Manual), or when the power cord is plugged in (Auto).   Manual             Auto

Sets the lamp power                                    Standard           Low

Sets the camera’s shutter speed to either (50Hz) or (60Hz). 50Hz            60Hz.

Sets the camera’s white balance to (Auto) or (Fixed). Auto            Fixed.

Description

Item

(Back hung 
from ceiling)

(Placed 
on floor)

(Rear)

(Hung from 

ceiling)

Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets

quieter. This setting will be cleared when you turn the power off. The setting will be back to
“Standard” when the power is turned on next time.

2: White balance, if set to Fixed, is reset upon power off and the Auto is resumed the next time the

unit is turned on. (Models with the document camera)

• Note that if Power on is set to Auto, then if the power cord is plugged in when power is

restored after a power outage, the projector power will come on.

• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.

Unplugging the power cord to cut off the power will shorten the life of the lamp.