Rotel RB-1092 用户手册

RB-1092 Stereo Power Ampliﬁer

AC Power and Control

AC Power Input

The RB-1092 is supplied with the proper AC
power cord. Use only this cord or an exact
equivalent. Do not use an extension cord. A
heavy duty multi-tap power outlet strip may
be used, but only if it is rated to handle the
current demand of the RB-1092.

Be sure the Power Switch on the front panel of
the RB-1092 is turned off. Then, plug one end
of the cord into the AC power connector

the back panel of the ampliﬁer. Plug the other
end into an appropriate AC outlet.

Your RB-1092 is conﬁgured at the factory for the
proper AC line voltage in the country where you
purchased it (USA: 120 volts/60 Hz, Europe:
230 volts/50 Hz). The AC line conﬁguration is
noted on a label on the back panel.

NOTE: Should you move your RB-1092 to
another country, it is possible to configure
your amplifier for use on a different line
voltage. Do not attempt to perform this con-
version yourself. Opening the enclosure of
the RB-1092 exposes you to dangerous volt-
ages. Consult a qualified technician or the
Rotel factory service department for infor-
mation.

If you are going to be away from home for
an extended period of time, it is a sensible
precaution to unplug your ampliﬁer.

Power Switch and

Indicator

The Power Switch is located on the front panel.
To turn the ampliﬁer on (or to activate either of
the optional automatic power-on modes), push
the switch in. The LED indicator above the switch
will light, indicating that the ampliﬁer is turned
on. To turn the ampliﬁer off, push the button
again and return it to the out position.

Turn On/Off Mode Selector

The RB-1092 can be turned on and off auto-
matically by using its “12V Trigger” system.
The Turn On/Off Mode Selector switch is used
to select which method is used.

• With the switch in the OFF position, the

amplifier is turned on or off manually using
the front panel power switch.

• With the switch in the 12V TRIG. position,

the amplifier is turned on automatically
when a 12 volt trigger signal is applied to
the 3.5mm Jack labeled IN. The front panel
POWER SWITCH overrides this function. It
must be ON for the +12V trigger to work.
Turning the switch OFF cuts power to the
amplifier, regardless of whether or not a
trigger signal is present.

+12V Trigger Input

and Output

The jack labeled IN is for connecting the 3.5mm
Plug/Cable carrying a +12 volt trigger signal
to turn the ampliﬁer on and off. To use this
feature the adjacent switch

must be set in

the 12V TRIG position (see previous section).
This input accepts any control signal (AC or
DC) ranging from 3 volts to 30 volts.

The jack labeled OUT is for connecting another
3.5mm plug/cable to provide a 12V trigger
signal to other components. The 12V output
signal is available whenever a +12 volt trigger
signal is applied to the IN connector.

Protection Indicators

Thermal and protection circuits protect the am-
pliﬁer against potential damage in the event of
extreme or faulty operating conditions. Unlike
many designs, the RB-1092’s protection circuit
is independent of the audio signal and has
no impact on sonic performance. Instead, the
protection circuit monitors the temperature of
the output devices and shuts down the ampliﬁer
if safe limits are exceeded.

In addition, the RB-1092 includes overcurrent
protection which operates only when load
impedances drop too low. This protection is
independent for each of the two channels.

Should a faulty condition arise, the ampliﬁer
will stop playing and the PROTECTION LED
on the front panel will light.

If this happens, turn the ampliﬁer off, let it
cool down for several minutes, and attempt to
identify and correct the problem. When you
turn the ampliﬁer back on, the protection circuit
will automatically reset and the PROTECTION
LED should go out.

In most cases, the protection circuitry activates
because of a fault condition such as shorted
speaker wires, or inadequate ventilation lead-
ing to an overheating condition. In very rare
cases, highly reactive or extremely low imped-
ance speaker loads could cause the protection
circuit to engage.

Input Signal Connections

See Figure 2

The RB-1092 has standard unbalanced RCA-
type input connectors, the type used on nearly
all audio equipment. There is an RCA input
for each of the two ampliﬁer channels. These
RCA inputs accept audio signals from pre-
ampliﬁers or surround sound processors. Use
high quality audio interconnect cables for best
performance.