Cisco Systems 3130 用户手册
32-14
Cisco Catalyst Blade Switch 3130 for Dell Software Configuration Guide
OL-13270-01
Chapter 32 Configuring SNMP
Configuring SNMP
The snmp-server host command specifies which hosts receive the notifications. The snmp-server
enable trap command globally enables the mechanism for the specified notification (for traps and
informs). To enable a host to receive an inform, you must configure an snmp-server host informs
command for the host and globally enable informs by using the snmp-server enable traps command.
enable trap command globally enables the mechanism for the specified notification (for traps and
informs). To enable a host to receive an inform, you must configure an snmp-server host informs
command for the host and globally enable informs by using the snmp-server enable traps command.
Step 5
snmp-server host host-addr
[informs | traps] [version {1 | 2c | 3
{auth | noauth | priv}}]
community-string [notification-type]
[informs | traps] [version {1 | 2c | 3
{auth | noauth | priv}}]
community-string [notification-type]
Specify the recipient of an SNMP trap operation.
•
For host-addr, specify the name or Internet address of the host (the
targeted recipient).
targeted recipient).
•
(Optional) Enter informs to send SNMP informs to the host.
•
(Optional) Enter traps (the default) to send SNMP traps to the host.
•
(Optional) Specify the SNMP version (1, 2c, or 3). SNMPv1 does
not support informs.
not support informs.
•
(Optional) For Version 3, select authentication level auth, noauth, or
priv.
priv.
Note
The priv keyword is available only when the cryptographic
universal software image is installed.
universal software image is installed.
•
For community-string, when version 1 or version 2c is specified,
enter the password-like community string sent with the notification
operation. When version 3 is specified, enter the SNMPv3 username.
enter the password-like community string sent with the notification
operation. When version 3 is specified, enter the SNMPv3 username.
•
(Optional) For notification-type, use the keywords listed in
. If no type is specified, all notifications are
sent.
Step 6
snmp-server enable traps
notification-types
notification-types
Enable the switch to send traps or informs and specify the type of
notifications to be sent. For a list of notification types, see
notifications to be sent. For a list of notification types, see
, or enter snmp-server enable traps ?
To enable multiple types of traps, you must enter a separate snmp-server
enable traps command for each trap type.
enable traps command for each trap type.
Note
When you configure a trap by using the notification type
port-security, configure the port security trap first, and then
configure the port security trap rate:
port-security, configure the port security trap first, and then
configure the port security trap rate:
•
snmp-server enable traps port-security
•
snmp-server enable traps port-security trap-rate rate
Step 7
snmp-server trap-source interface-id
(Optional) Specify the source interface, which provides the IP address for
the trap message. This command also sets the source IP address for
informs.
the trap message. This command also sets the source IP address for
informs.
Step 8
snmp-server queue-length length
(Optional) Establish the message queue length for each trap host. The
range is 1 to 1000; the default is 10.
range is 1 to 1000; the default is 10.
Step 9
snmp-server trap-timeout seconds
(Optional) Define how often to resend trap messages. The range is 1 to
1000; the default is 30 seconds.
1000; the default is 30 seconds.
Step 10
end
Return to privileged EXEC mode.
Step 11
show running-config
Verify your entries.
Step 12
copy running-config startup-config
(Optional) Save your entries in the configuration file.
Command
Purpose