KitchenAid W10056407A 安装指导
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
installation. Read and follow the instructions provided with
any tools listed here.
All Installations
Tools needed:
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
Parts supplied:
Make sure all these parts are included in the literature package.
Parts needed:
4 #10 x 1/2" wood screws (if installing custom front panels)
Wire stripper
Small
tubing cutter
Electric drill
with 1/2”, 3/4”
and 1 1/2” hole
saw bits
with 1/2”, 3/4”
and 1 1/2” hole
saw bits
Pliers
UL listed or CSA
approved twist-on
wire connectors*
approved twist-on
wire connectors*
5/8” open-end
wrench
wrench
Small level
Utility knife
Phillips
screwdriver
screwdriver
Measuring tape
or ruler
or ruler
10” adjustable wrench
that opens to
1.18” (2.9 cm)
that opens to
1.18” (2.9 cm)
Flat-blade
screwdriver
screwdriver
5/16” and 1/4”
nut drivers or
hex sockets
nut drivers or
hex sockets
If installing custom front panels,
Torx T15 screwdriver
Torx T15 screwdriver
INSTALLATION REQUIREMENTS
90° Elbow fitting with 3/8”
N.P.T. external threads (the
other end must fit your water
supply line)
N.P.T. external threads (the
other end must fit your water
supply line)
Teflon
®
tape or pipe
joint compound
Drain hose
2 - Drain hose clamps
(1 large and 1 small)
(1 large and 1 small)
2 - #10 x 1/2”
Phillips-head
screws
Phillips-head
screws
Green
Silver
Copper tubing (3/8”
O.D. suggested) or
flexible braided
water supply line
flexible braided
water supply line
For Direct Wire:
use UL listed or
CSA approved
strain relief to
fit 7/8” (2.2 cm)
hole
CSA approved
strain relief to
fit 7/8” (2.2 cm)
hole
See “Electrical Requirements” section
For Power Supply
Cord: use UL
listed power
supply cord kit
marked for use
with dishwasher
Cord: use UL
listed power
supply cord kit
marked for use
with dishwasher
Flashlight
Bath towel
Wood block
Shallow pan
3
1 1/2”–2”
(38.1–5.0 cm)
Screw-typ e
clamps (3 max)
(38.1–5.0 cm)
Screw-typ e
clamps (3 max)
Masking or
duct tape
duct tape
2 #8x1-3/8” Torx
®
T15 screws
4 #10x3/8” hex-head screws
Bottom sound pad (located
in lower rack)
in lower rack)
Moisture barrier tape
Other parts you may also need:
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section. It is recommended that
electrical connections be made by a licensed electrical installer.
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first-time installations
Tools needed:
Parts needed:
Additional parts supplied with top-venting models only:
Additional parts supplied with certain models only:
Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-422-1230.
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
†® TORX is a registered trademark of Acument Intellectual Properties, LLC.