KitchenAid KUDD03STBL 用户手册
6
You must have:
■
120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical
supply.
supply.
■
Copper wire only.
We recommend:
■
A time-delay fuse or circuit breaker.
■
A separate circuit.
If direct wiring dishwasher:
■
Use flexible, armored or nonmetallic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
■
Use strain relief method provided with house wiring junction
box or install a UL-listed/CSA-certified clamp connector to
the house wiring junction box. If using conduit, use a
UL-listed/CSA-certified conduit connector.
box or install a UL-listed/CSA-certified clamp connector to
the house wiring junction box. If using conduit, use a
UL-listed/CSA-certified conduit connector.
If connecting dishwasher with a power supply cord:
■
Use Power Supply Cord Kit (Part Number 4317824) marked
for use with dishwashers. Kit contents include:
for use with dishwashers. Kit contents include:
■
Voltex, Inc., UL listed 16 gauge 3 wire power supply cord
with 3 prong grounded plug.
with 3 prong grounded plug.
■
Neer C-500
⁷⁄₈
" strain relief.
■
3 wire connectors.
■
Part Number 302797 grommet.
Follow the kit instructions for installing the power supply
cord.
cord.
■
Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
IMPORTANT: If you plan to install a garbage disposer, an
additional separate 120-volt, 60 Hz, AC-only, 15 or 20 amp fused
electrical supply is required.
additional separate 120-volt, 60 Hz, AC-only, 15 or 20 amp fused
electrical supply is required.
Water Supply Requirements
■
A hot water line with 20-120 psi (138-862 kPa) water
pressure.
pressure.
■
120°F (49°C) water temperature at dishwasher.
■
Flexible stainless steel braided fill line (½" minimum plastic
tubing is not recommended).
tubing is not recommended).
Drain Requirements
■
Use the new drain hose supplied with your dishwasher. If this
is not long enough, use a new drain hose with maximum
length of 12 ft (3.7 m) that meets all current AHAM/IAPMO
test standards, is resistant to heat and detergent, and fits the
1" (2.5 cm) drain connector of the dishwasher.
is not long enough, use a new drain hose with maximum
length of 12 ft (3.7 m) that meets all current AHAM/IAPMO
test standards, is resistant to heat and detergent, and fits the
1" (2.5 cm) drain connector of the dishwasher.
■
Connect drain hose to waste tee or disposer inlet above drain
trap in house plumbing and 20" (50.8 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or
be connected to an air gap.
trap in house plumbing and 20" (50.8 cm) minimum above the
floor. It is recommended that the drain hose either be looped
up and securely fastened to the underside of the counter, or
be connected to an air gap.
INSTALLATION INSTRUCTIONS
1. Disconnect power.
2. Turn off water supply.
Unpack Dish Drawer
1. Read valuable information on exterior of shipping box before
opening.
2. Remove shipping materials, tape and film from the
dishwasher. Remove parts package from inside the
dishwasher.
dishwasher.
WARNING
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Electrical Shock Hazard
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
dishwasher.
Failure to do so can result in back or other injury.