Bosch 2 x 14" sds-max scaling chisel 参考指南

A

D

E

F

C

B

A

D

C

B

84540M 1-3/4"

13/16"

1/2"

2-5/16"

Micrograin control-cut bit used to create clean, simple lines to 

accentuate a surface.

f

f

  Recommended for use with a router table
f

f

 Minimum recommended panel thickness is 3/4"

Carbide-Tipped Cove Raised-Panel Cutter

Micrograin control-cut bit creates easy-open door or drawer edges 

that eliminate metal pulls and enhance the hardwood effect.

f

f

 Recommended for use with a router table

Carbide-Tipped Finger Pull Bit

85641M 3-3/8" 1/2"

1/2"

2-7/8" 1/2"

1-9/16" 1-7/16"

A

D

E

F

C

B

Micrograin bits produce raised-panel cuts along straight- and curved- 

panel edges.

f

f

  These bits are not for use in hand-held routers. Use with a router 

table only

f

f

 Minimum recommended panel thickness is 3/4"

Carbide-Tipped Ogee Raised- 

Panel Cutters

A

D

E

C

B

Micrograin bits used to flush-face frame to cabinet side while at 

the same time cutting a V-groove down cabinet joint. Also used for 

creating a decorative V-groove cut.

Carbide-Tipped Face Frame/Flush Trim, 

V-Groove Bits

85638M 2-5/8" 5/8"

1/2"

2-1/2" 1/2"

3/4"

1-1/16"

85640M 3-3/8" 9/16"

1/2"

2-1/2" 1/2"

7/8"

1-7/16"

85646M 5/8"

1"

1/4"

2-1/2" 90˚

1/2"

85647M 5/8"

1"

1/2"

3"

90˚

1/2"

A

D

E

C

B

RW

Micrograin control-cut bits for making rabbeting cuts without the use 

of a router guide.

f

f

  To increase the width of rabbet by 1/16" for 85218M and 85590M, 

purchase 3/8" diameter bearing 3600900501 and dust shield 

3600120507

Carbide-Tipped Rabbeting Bits

85218M 3/8"

1-1/4"

1/2"

1/4"

2"

1/2"

85590M 3/8"

1-1/4"

1/2"

1/2"

2-3/8" 1/2"

85614M 1/2"

1-3/8"

1/2"

1/4"

2"

1/2"

85615M 1/2"

1-3/8"

1/2"

1/2"

2-3/8" 1/2"

A

D

C

B

Micrograin bits for making dovetail joints.

Carbide-Tipped Dovetail Bits

3/8"

3/8"

1/2"

2"

9˚

3/8"

3/8"

3/8"

2"

9˚

1/2"

1/2"

1/4"

2"

14˚

1/2"

1/2"

1/2"

2-5/16"

14˚

17/32"

1/2"

1/4"

1-7/8"

15˚

3/4"

3/4"

1/2"

3"

14˚

1"

1"

1/2"

2-3/4"

14˚

A

D

R

E

F

G

C

B

A

D

E

F

G

R

C

B

Micrograin bits with shear-angle geometry, super-sharp 

cutting edges and close-tolerance manufacturing to ensure 

consistently smooth, tight-fitting joints.

f

f

  Recommended for use with a router table. Designed 

for 3/4" wood with a maximum wood thickness of 7/8"

f

f

  85621M is a control-cut bit

Carbide-Tipped Beading Stile 

and Rail Bits

1-5/8"

5/8"

1/2"

3"

5/8"

1/4"

7/8"(22 mm)

7/32"

1-5/8"

57/64"

1/2"

3"

1-5/8"

1/4"

7/8"(22 mm)

1/2"

Beading stile and rail set includes 85621M and 85622M assemblies

R

out

er Bits

For more details visit 

248 | 2012/2013 Power Tools & Accessories Catalog