Toshiba tdp-tw355u 用户手册

45

44

[

]: Displays the 

menu.

Toggle with 

 

 buttons and press 

 button. (The input without signals can be

selected.)

[

]

Note that if [

] is set to [

], then if the 

is ON when

power is restored after a power outage, the projector will come on.

[

]

<

>: Switches on/off the automatic keystone distortion correction when the

EASY SETUP button is pressed or when Power on Easy setup is set to 

.

<

>: Switches on/off the auto-setting function when the 

button is pressed or when Power on Easy setup is set to 

.

<

>: Switches 

 the Easy setup operation when the power is

turned on.

• The Easy setup automatically switches off when [

] or [

] is

selected for projection mode.

[

]

When [

] is set to [

], the screen becomes a little darker, but the cooling

fan noise gets quieter.

• The lamp power selection that you made will not be switched in about 1 minute after

the power is on.

• For lamp protection, even it has been set to [

], the lamp power mode stays in

[

] in about 1 minute after the power is on, and then it will be switched to

your desired selection mode.

[

]

Setting [

] to [

] increases the cooling fan speed. Set this option to use the

projector, for example, at high altitude (over 1,500 meters above sea level).

[

]

When [

] is set to [

], the wireless LAN is switched to the standby state

as the projector enters standby. While the wireless LAN is in standby, the projector can be
powered on using the remote control function of the Wireless Utility.
When [

] is set to [

], the projector cannot be powered on with the

remote control function of the Wireless Utility.

[

]

Sets a remote control code from 4 types. You can set each code respectively for up to 4
projectors. The factory setting is [

].

To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the remote

control do not match.

Remove the battery cover and set the same 

as the projector. 

 (Use a screwdriver with thin tip to set.)

[

]

Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done.
• To release the key lock, press the control panel’s 

button for 10 seconds. The

key lock is released with a beep sound.

    /    shows whether signal is 
 input or not.

■ The default setting menu

This menu shows placement status and other settings.

Description

Item

When projecting on a non-screen surface, select a color in accordance 
with the projecting surface.
Press      and switch with       and      . 

Set the time to wait for the power to be turned off after the last 
operation is made with no input signal.
Press      and switch with       and      .

 (not turned off)/

/

/

/

/

Set whether the input with signals is only selected or not.

Sets whether to turn on the power when the 

 button is pressed 

(Manual), or when the main power switch is turned on (Auto).  

Set the items of Easy setup and power ON/OFF.
[      or      : Enter setting mode]     [          : Select item]     [

]

      

      

      

      

Sets the lamp power. 

Sets the cooling fan speed.

Switch on/off the wireless LAN while the projector is in standby.
When two or more projectors are used and controlled by the remote 
control respectively, this menu sets the code for the projector and the 
remote control.
[      or      : Enter setting mode]      [           : Select item]      [           :
Select from 

, 

, 

, 

]      [     :Confirm]      [           :Select 

to end]  

Press [

] to return.

Lock the control panel buttons.
[      or      : Enter setting mode]      [           : Select item]      [           : 
Select 

]      [     :Confirm]      [           :Select 

to end]  

Press [

] to return.

Press       . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password function
When [

] is [

], the Password Setting screen is displayed.

(Rear ceiling)

(Standard)

(Rear)

(Ceiling)

 

[

]

Projects the image in colors more like projecting on a screen.

• The projected image may differ depending on the type, color,

and material of the blackboard and wall even if the selected
color is the same as the projected screen.

[

]

[

]: Automatically searches the signals that can be

projected, and switches input from the connected device
that outputs the signals each time the 

button is

pressed. The input from the connected device that
outputs no signals is skipped.