Toshiba tlp-wx100 用户指南
24
25
Operations
Connecting the power cord
1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.
The ON/STANDBY indicator will change to orange,
indicating standby mode.
indicating standby mode.
Turning the power on
1
Removing the lens cap
Be sure to remove the lens cap when the power is turned on. If the cap is left on the
projector, it could become deformed due to heat.
projector, it could become deformed due to heat.
2
Press the ON/STANDBY button.
The power turns on with a beep sound (if the beep
sound is set to [
On]), and the ON/STANDBY indicator
flashes green. After a moment, the start-up screen
appears.
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the
bottom of the unit. Doing so could result in injury and/or damage the object.
•
•
•
Notes
The start-up screen will disappear after a moment. You can configure the system to
prevent the start-up screen from appearing. To do this, use the
Display setting menu
.
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
.
You can disable the beep sound in the
Default setting 1 menu
.
When [
Key lock] is [On], the operation buttons of the projector do not work
.
When [
Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears
.
Do not touch the lens directly with your hand.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
■
■
•
•
•
•
•
•
Turning the power on and off
Operations
Power cord connector
(Supplied)
Control panel
Remote
control
Turning the power off
1
Press the ON/STANDBY button.
When the setting of beep sound is [
On], the projector beeps, and a message appears
on the screen, confirming that you wish to shut off the power. To shut off the power,
press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a
while without conducting any operations. This message will disappear after a moment.
(This operation is no longer valid after the message disappears.)
press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a
while without conducting any operations. This message will disappear after a moment.
(This operation is no longer valid after the message disappears.)
2
Press the ON/STANDBY button again.
When the setting of beep sound is [
On], the projector
beeps, and the screen disappears, but the internal
cooling fan continues to operate. Then, the projector
goes into standby mode.
During cooling, the ON/STANDBY indicator flashes.
While the indicator is flashing, the power can not be
turned back on. There is no problem with unplugging
the power cord in this state.
3
Replace the lens cap.
After use, replace the lens cap.
Note
The projector consumes about 4.5W of power in standby. We recommend that you
unplug the power cord if you will not be using the projector for an extended period.
unplug the power cord if you will not be using the projector for an extended period.
Precautions
When you wish to restart the projector again right after turning off the power, give the
lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it
may fail to light.
Right after turning off the power, the unit may become very hot, especially air exhaust,
lamp cover or the bottom of the unit. Please handle with care to avoid burn injuries.
lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it
may fail to light.
Right after turning off the power, the unit may become very hot, especially air exhaust,
lamp cover or the bottom of the unit. Please handle with care to avoid burn injuries.
■
•
•
•
Control panel
Remote
control