3M SCP712 补充手册
3M
™ Super Close Projection System SCP712
Product Safety Guide
© 3M 2008. All Rights Reserved
3
•
To reduce the risk associated with exposure to hazardous voltage:
- Do not remove any screws other than those specified in the lamp replacement instructions.
- Do not remove any screws other than those specified in the lamp replacement instructions.
•
To reduce the risk associated with hazardous voltage:
- Do not operate this projector in wet environments or outdoors.
- Do not modify this projector or power cord.
- Do not attempt to service the projector; other than the lamp cartridge there are no user serviceable parts inside the
projector.
- Contact a 3M authorized service provider for service.
- Disconnect power cord when the projector is not in use, during lamp replacement, and while cleaning.
- Do not allow water or other liquids to enter the projector.
- Do not operate this projector in wet environments or outdoors.
- Do not modify this projector or power cord.
- Do not attempt to service the projector; other than the lamp cartridge there are no user serviceable parts inside the
projector.
- Contact a 3M authorized service provider for service.
- Disconnect power cord when the projector is not in use, during lamp replacement, and while cleaning.
- Do not allow water or other liquids to enter the projector.
•
To reduce the risk associated with hazardous voltage and/or fire:
- Replace power cord if damaged.
- Contact a 3M authorized service provider if the projector becomes damaged.
- Use a grounded extension cord with a rating at least equal to that of the projector.
- Connect this projector to a grounded outlet.
- Replace power cord if damaged.
- Contact a 3M authorized service provider if the projector becomes damaged.
- Use a grounded extension cord with a rating at least equal to that of the projector.
- Connect this projector to a grounded outlet.
•
To reduce the risk associated with hot surface of lamp cartridge:
- Unplug the projector from the electrical outlet and allow the lamp to cool for 60 minutes before replacing the lamp.
- Unplug the projector from the electrical outlet and allow the lamp to cool for 60 minutes before replacing the lamp.
•
To reduce the risk associated with choking:
- Keep the battery and battery cover away from children and pets.
- Keep the battery and battery cover away from children and pets.
•
To reduce the risk associated with environmental contamination due to mercury:
- Hg: Lamp contains mercury. Don't throw in trash. Dispose according to local, state, or federal laws.
See www.lamprecycle.org or call 1-800-328-1371.
- Hg: Lamp contains mercury. Don't throw in trash. Dispose according to local, state, or federal laws.
See www.lamprecycle.org or call 1-800-328-1371.
•
To reduce the risk associated with lamp rupture related hazards:
- In event of lamp rupture, call 3M authorized service provider for repair. Ruptured lamp repair is not user serviceable.
- Wash your hands thoroughly if contact with ruptured lamp debris has taken place.
- Ventilate the area where the lamp rupture occurs. The lamp operates at high temperature.
- In event of lamp rupture, call 3M authorized service provider for repair. Ruptured lamp repair is not user serviceable.
- Wash your hands thoroughly if contact with ruptured lamp debris has taken place.
- Ventilate the area where the lamp rupture occurs. The lamp operates at high temperature.
•
To reduce the risk associated with hazard voltage, and/or impact, and/or tripping, and/or intense visible light:
- Do not use this projector around unsupervised children.
- Do not use this projector around unsupervised children.
•
To reduce the risk associated with sharps, premature lamp failure, exposure to mercury:
- Always handle the fragile lamp module with care.
- Replace the lamp module when the lamp replacement message appears.
- Never replace the lamp module with a previously used lamp module.
- Always handle the fragile lamp module with care.
- Replace the lamp module when the lamp replacement message appears.
- Never replace the lamp module with a previously used lamp module.
•
To reduce the risk associated with intense visible light:
- Avoid looking directly into the projector lens while the lamp is on.
- Avoid looking directly into the projector lens while the lamp is on.
•
To reduce the risk associated with impact of a falling projector:
- Use only the 3M brand wall/ceiling mounting hardware kit if wall or ceiling mounting is desired.
- Installation of the 3M brand wall/ceiling kit must only be performed by qualified personnel.
- Adhere strictly to the proper installation procedure as outlined in the installation instructions when installing the 3M
wall/ceiling kit.
- Always operate the unit on a flat, sturdy, and horizontal surface.
- Use only the 3M brand wall/ceiling mounting hardware kit if wall or ceiling mounting is desired.
- Installation of the 3M brand wall/ceiling kit must only be performed by qualified personnel.
- Adhere strictly to the proper installation procedure as outlined in the installation instructions when installing the 3M
wall/ceiling kit.
- Always operate the unit on a flat, sturdy, and horizontal surface.
•
To reduce the risk associated with explosion, and/or chemicals from leaking battery:
- Use only with battery type AAA.
- Orient the battery’s plus (+) and minus (-) terminals according to the markings found on the remote control.
- Do not leave the battery in the remote for an extended period of time.
- Do not heat, disassemble, short, recharge, or expose the batteries to fire or high temperature.
- Do not carry batteries loose in your pocket or purse.
- Avoid eye and skin contact in the event that battery would leak.
- Do not mix used and new batteries.
- Use only with battery type AAA.
- Orient the battery’s plus (+) and minus (-) terminals according to the markings found on the remote control.
- Do not leave the battery in the remote for an extended period of time.
- Do not heat, disassemble, short, recharge, or expose the batteries to fire or high temperature.
- Do not carry batteries loose in your pocket or purse.
- Avoid eye and skin contact in the event that battery would leak.
- Do not mix used and new batteries.
•
To reduce the risk associated with tripping, and/or impact:
- Position the power cord and data cable so that they can not be tripped over.
- Position the power cord and data cable so that they can not be tripped over.
•
To reduce the risk associated with environmental contamination due to battery chemicals:
- Dispose of exhausted batteries in accordance with applicable federal, state and local regulations.
- Dispose of exhausted batteries in accordance with applicable federal, state and local regulations.
SAVE THESE INSTRUCTIONS
WARNING
English
CAUTION