KitchenAid KBSD608EBS 安装指南

INSTALLATION REQUIREMENTS

Tools and Parts

■

Installer: Leave Installation Instructions with the homeowner.

■

Homeowner: Keep Installation Instructions for future 
reference. Save these Installation Instructions for the local 
electrical inspector’s use.

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here. 

■

#8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)

■

2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)

■

Make custom panels or consult a qualified cabinetmaker or 
carpenter to make the panels. 

Overlay Series: Make custom panels, or consult a qualified 
cabinetmaker or carpenter to make the panels. See “Overlay 
Series Custom Panels and Handle Kits” for more information.

Stainless is shipped complete. 

■

If you are connecting the water line directly to copper tubing 
and not to a shutoff valve, you need a ferrule, a union, and a 

¹⁄₄" (6.35 mm) compression fitting. 

Location Requirements

The refrigerator can be recessed in an opening between cabinets 
or installed at the end of a cabinet run using a side panel to 
enclose the refrigerator.

■

Observe all governing codes and ordinances. 

■

It is recommended that you do not install the refrigerator near 
an oven, radiator, or other heat source. 

■

Do not install in a location where the temperature will fall 
below 55°F (13°C).

■

Floor must support the refrigerator weight, more than 600 lbs 
(272 kg), door panels and contents of the refrigerator. 

■

Ceiling height must allow for side tipping radius. See “Tipping 
Radius.”

■

Location should permit door to open fully. See “Door Swing 
Dimensions.” 

■

Location must permit top grille removal. See “Opening 
Dimensions.”

■

To avoid tipping during use, the solid soffit must be within 1" 
(2.5 cm) maximum above the refrigerator. If the solid soffit is 
higher than 1" (2.5 cm) or one is not available, then the 
refrigerator must be braced. 

If anti-tip boards are needed, they must be installed to the 
rear wall studs so that the bottom of the anti-tip board is 84" 
(213.4 cm) from the floor. See “Install Anti-Tip Boards” for 
more information.

NOTES:  

■

A clearance of 

¹⁄₂" (1.3 cm) must be maintained above the 

top grille in order for the top grille to be removed.

■

Do not remove the foam gasket on top of the compressor 
cover unless removal is necessary to fit the unit under a 
soffit. Removal of the gasket will cause loss in cooling 
efficiency. 

■

If installing under a solid soffit, after installation raise the 
leveling legs so that the gasket is pressed snugly against 
the soffit. 

■

A grounded 3 prong electrical outlet should be located within  
a specified number of inches from the right-hand side 
cabinets or end panel. See the chart following the graphic for 
the number of inches required for your model. For more 
information, see “Electrical Requirements.”

■

Cordless drill

■

Drill bits

■

Adjustable 
wrenches (2)

■

Phillips screwdriver

■

Small level

■

Appliance dolly

■

Torx

®†

T27 screwdriver

■

¹¹⁄₃₂" nut driver

■

³⁄₈" and ¹⁄₂" open-end wrenches

■

⁵⁄₃₂" hex key

■

¹⁄₄" and ⁵⁄₁₆" socket drivers

■

Tape measure

■

Utility knife

†®TORX is a registered trademark of Acument Intellectual Properties, LLC

B

A