KitchenAid KDRS483VSS 安装指南
24
6. Place Natural gas orifice in plastic parts bag for future use
and keep with package containing literature.
NOTE: There may be extra orifices in your kit.
NOTE: There may be extra orifices in your kit.
7. Replace the burner base.
8. Replace burner cap.
9. Repeat steps 2 through 8 for the remaining burners.
8. Replace burner cap.
9. Repeat steps 2 through 8 for the remaining burners.
To Convert Grill Burner (on some models)
1. Remove grill grate, wave plate, flame spreader, and burner
assembly. See the “Install Grill Grease Trays” section for
removal instructions. Set parts aside.
2. Use a
1
/
2
" deep-well socket to remove the Natural gas orifice
hood. Replace with correct grill LP gas orifice hood. See the
“LP Gas Orifice Spud/Hood Chart.”
3. Turn LP gas orifice hood down tightly onto orifice base.
4. Place Natural gas orifice hoods in plastic parts bag for future
4. Place Natural gas orifice hoods in plastic parts bag for future
use and keep with package containing literature.
5. Before replacing the burner assembly, loosen the screw at
the front of the burner and rotate the shutter so that the
opening is
5
/
16
" (8.0 mm) wide.
6. Reinstall the burner assembly, flame spreader, wave plate,
and grill grate. See the “Install Grill Grease Trays” section for
installation instructions.
7. Open shut-off valve in the gas supply line. The valve is open
when the handle is parallel to the gas pipe.
REMEMBER: Once you have completed converting the
REMEMBER: Once you have completed converting the
grill, test the range for leaks by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show,
indicating a leak. Correct any leaks found.
8. Plug in range or reconnect power.
Complete Installation
1. Refer to the “Make Gas Connection” section for properly
connecting the range to the gas supply.
2. Refer to the “Electronic Ignition System” section for proper
burner ignition, operation, and burner flame adjustments.
IMPORTANT: You may have to adjust the Lo setting for
IMPORTANT: You may have to adjust the Lo setting for
each cooktop burner.
Checking for proper cooktop burner flame is very important.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
1
/
4
" (0.64 cm) to
1
/
2
" (1.3 cm) long. The outer cone is not
as distinct as the inner cone. LP gas flames have a slightly
yellow tip.
3. Refer to “Complete Installation” in the “Installation
Instructions” section of this manual to complete this
procedure.
Natural Gas Conversion
1. Turn the manual shut-off valve to the closed position.
2. Unplug range or disconnect power.
A
A. Grill orifice hood location
A
B
A. Shutter opening
B. Screw
B. Screw
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
Failure to follow these instructions can result in death
or serious burns to children and adults.
A. To range
B. Shut-off valve (closed position)
C. Gas supply line
B. Shut-off valve (closed position)
C. Gas supply line
A
B