KitchenAid 27-Inch Double Wall Oven, Architect® Series II 安装指南

Gather the required tools and parts before starting installation. 

Read and follow the instructions provided with any tools listed 

here.

■

 

Phillips screwdriver

■

 

Measuring tape

■

 

Hand or electric drill (for wall cabinet installations)

■

 

1" (2.5 cm) drill bit (for wall cabinet installations)

■

 

Level

■

 

Flat-blade screwdriver

■

 

UL listed or CSA approved conduit connector

■

 

UL listed wire connectors

■

 

#8-14 x 1" screws – single ovens (2), double ovens (4)

■

 

Two #8-18 x ³⁄

8

" screws – bottom vent

■

 

Four #8-18 x ¹⁄

4

" screws – bottom vent trim

■

 

Four #8-18 x ³⁄

8

" screws – double oven feet

■

 

Bottom vent

■

 

Bottom vent trim

■

 

Two feet – double oven

■

 

Two front feet – double oven

■

 

Four grommets – single ovens (2), double ovens (4)*

■

 

Foam strip – single oven**

Check local codes. Check existing electrical supply.  

See “Electrical Requirements.”
It is recommended that all electrical connections be made  

by a licensed, qualified electrical installer.
*Grommets not included with models KEBK171B, KEBK101B, 

KEBK276B, KEBK206B, KEBS179B, KEBS109B, KEBS277B, 

KEBS279B, KEBS207B, KEBS209B, KEBU109B and 

KEBU209B.
**Foam strip not included with double oven.

IMPORTANT: Observe all governing codes and ordinances. 

■

 

Cabinet opening dimensions that are shown must be used. 

Given dimensions provide minimum clearance with oven.

■

 

Recessed installation area must provide complete 

enclosure around the recessed portion of the oven.

■

 

Grounded electrical supply is required. See “Electrical 

Requirements” section.

■

 

Electrical supply junction box should be located 3"  

(7.6 cm) maximum below the support surface when the 

oven is installed in a wall cabinet. A 1" (2.5 cm) minimum 

diameter hole should have been drilled in the right rear or 

left rear corner of the support surface to pass the appliance 

cable through to the junction box.

  

NOTE: For undercounter installation, it is recommended 

that the junction box be located in the adjacent right or left 

cabinet. If you are installing the junction box on rear wall 

behind oven, it is recommended that the junction box be 

recessed and located in the upper center of the cabinet

■

 

Oven support surface must be solid, level and flush with 

bottom of cabinet cutout.

■

 

Floor must be able to support a single oven weight of  

129 lbs (59 kg) for 27" (68.6 cm) models or 154 lbs (70 kg) 

for 30" models (76.2 cm).

■

 

Floor must be able to support a double oven weight  

of 251 lbs (114 kg) for 27" (68.6 cm) models or 288 lbs  

(131 kg) for 30" (76.2 cm) models.

  

IMPORTANT: To avoid damage to your cabinets, check 

with your builder or cabinet supplier to make sure that the 

materials used will not discolor, delaminate or sustain other 

damage. This oven has been designed in accordance with 

the requirements of UL and CSA International and complies 

with the maximum allowable wood cabinet temperatures of 

194°F (90°C).

Ovens approved for this type of installation have an approval 

label located on the top of the oven. Refer to undercounter 

installation instructions for cutout dimensions and approved 

oven cooktop combinations (separate sheet).