Tele 111100 Time Delay Relay, Timer, DPDT-CO 12 - 240 V DC/AC 111100 用户手册

The supply voltage U must be constantly applied to the device (green 

LED U/t illuminated). When teh control contact S is closed, the set 

interval t begins (green LED U/t flashes). After the interval t has expired 

(green LED U/t illuminated) the output relay R switches into on-position 

(yellow LED illuminated). This status remains until the control contact is 

opened again. If the control contact is opened before the interval t has 

expired , the interval already expired is erased and is restarted with the 

next cycle.

U

U/t

S

R

LED

When the supply voltage U is applied, the output relay R switches 

into on-position (yellow LED illuminated) and the set interval t begins 

(green LED U/t flashes). After the interval t has expired (green LED U/t 

illuminated) the output relay switches into off-position (yellow LED not 

illuminated). This status remains until the supply voltage is interrupted. 

If the supply voltage is interruted before the interval t has expired, the 

output relay switches into off-position. The interval already is erased and 

is restarted when the supply voltage is next applied.

U

U/t

R

LED

When the supply voltage U is applied, the set interval t begins (green 

LED U/t flashes). After the interval t has expired, the output relay R 

switches into on-position (yellow LED illuminated) and the set interval t 

begins again. After the interval t has expired, the output relay switches 

into off-position (yellow LED not illuminated). The output relay is 

triggered at a ratio of 1:1 until the supply voltage is interrupted.

U

U/t

R

LED

When the supply voltage U is applied, the set interval t begins (green 

LED U/t flashes). After the interval t has expired (green LED U/t 

illuminated) the output relay R switches into on-position (yellow LED 

illuminated). This status remains until the supply voltage is interrupted.

If the supply voltage is interrupted before the expiry of the interval t, 

the interval already expired is erased and is restarted when the supply 

voltage is next applied.

U

U/t

R

LED

The supply voltage U must be constantly applied to the device (green 

LED U/t illuminated). When the control contact S is closed, the output 

relay R switches into on-position (yellow LED illuminated). If the control 

contact is opened, the set interval t begins (green LED U/t flashes). 

After the interval t has expired (green LED U/t illuminated) the output 

relay switches into off-position (yellow LED not illuminated). If the control 

contact is closed again before the interval t has expired, the interval 

already expired is erased and is restarted.

U

U/t

S

R

LED

The supply voltage U must be constantly applied to the device (green 

LED U/t illuminated). When the control contact S is closed, the output 

relay R switches into on-position (green LED U/t illuminated) and the set 

interval t begins (green LED U/t flashes). After the interval t has expired 

(green LED U/t illuminated) the output relay switches into off-position 

(yellow LED not illuminated). During the interval, the control contact can 

be operated any number of times. A further cycle can only be started 

when the cycle run has been completed.

U

U/t

S

R

LED

The supply voltage U must be constantly applied to the device (green 

LED U/t illuminated). Closing the control contact S has no influence 

on the condition of the output R. When the control contact is opened, 

the output relay switches  into on-position (yellow LED illuminated) 

and the set interval t begins (green LED U/t flashes). After the interval 

t has expired (green LED U/t illuminated), the ouput relay switches into 

off-position (yellow LED not illuminated). During the interval, the control 

contact can be operated any number of times. A further cycle can only 

be started when the cycle run has been completed.

U

U/t

S

R

LED