Behringer Europower PMP2000 用户手册

EUROPOWER PMP2000 User Manual

(12) 

The CD/TAPE/LINE IN RCA input of channel 13/14 allows you to feed in 

external stereo signals from your CD player or tape deck, for example.

(13) 

The CD/TAPE/LINE OUT RCA output provides the stereo main mix signal of 

your PMP2000 and can be routed to, say, a recording machine.

(14) 

The phantom power supply provides the voltage necessary for the operation 

of condenser microphones. Use the PHANTOM POWER switch to activate 

the supply together for channels 1 - 12 (XLR connector). The LED above the 

switch is lit when phantom power is on.

(15) 

This is the PMP2000’s graphic stereo equalizer, which comprises two units 

and can be used to adapt the sound to the room acoustics.

The stereo equalizer is effective on the main mix when both units have been 

activated with the EQ IN buttons  

(16)

  and the MODE switch  

(21)

  is set to its 

upper position (“LEFT/RIGHT”).

The stereo equalizer uses one unit each to process the main and monitor 

mix signals, if both units are on and the MODE switch  

(21)

  is set to its lower 

position (“MON/MAIN”).

(16) 

Use the EQ IN buttons to switch the two equalizer units on or off.

(17) 

Press the RUMBLE FILTER button to activate the low-cut filter of 

channels 1 - 6. This filter eliminates unpleasant bass frequencies 

(e.g. microphone pop noise).

(18) 

The FX TO MON control determines the effects intensity of the multi-effects 

processor as part of the monitor mix. Turn the control fully counter-clockwise 

to add no effect to the monitor mix.

(19) 

The MONITOR LEVEL control adjusts the volume of the monitor mix.

(20) 

Use the MONITOR LEVEL display to control the monitor signal level. 

The upper LED (LIM) lights up when the built-in limiter is activated, 

thus protecting against overload.

(21) 

With this MODE switch you can determine whether the PMP2000 works as a 

stereo amplifier (“LEFT/RIGHT”) or as a dual mono amplifier (“MON/MAIN”). 

Please note that the equalizer function also depends on this switch setting 

(see  

(15)

).

(22) 

The FX TO MAIN control functions as FX return for the built-in effects 

processor. Use this control to add the desired effect signal to the main mix. 

No effect signal is added when the FX TO MAIN is set fully counter-clockwise.

(23) 

The MAIN LEVEL control governs the overall volume of the PMP2000.

(24) 

The MAIN LEVEL display reads the output level of the PMP2000. The upper 

LED (LIM) lights up when the built-in limiter is activated, thus protecting 

against signal peaks.

(25) 

Use the FX FOOTSW(itch) jack to connect any commercially available foot 

controller. It allows you to bypass the effects unit.

(26) 

This is the balanced MONITOR output of your PMP2000. Use it to feed an 

external monitor amp or active wedge.

(27) 

These two ¼" TS jacks allow you to route the output signal to an external 

amplifier. This allows you to, say, use only the mixing and effect section of 

the PMP2000. The signal is taken pre-power amp. Of course, you can also use 

only the left jack as a mono output.

(28) 

These two ¼" TS jacks can be used to connect external signals, such as the 

main mix signal from an additional mixing console (pre-power amp).

(29) 

Here, you will find a list of all multi-effect presets available.

(30) 

This is the LED level meter of the effects processor. Please make sure that the 

clip LED lights up with signal peaks only. If it is lit constantly, this indicates 

that the effects processor is overdriven, which can lead to unpleasant 

distortion.

(31) 

The Effect display reads the currently selected preset.

(32) 

Turn the PROGRAM control to select the effect presets. Press the control 

briefly to confirm your selection.

(33) 

The mains connection is on a standard IEC receptacle. An appropriate power 

cord is supplied with the unit.

(34) 

FUSE HOLDER. Before connecting the unit to the mains, ensure that the 

voltage setting matches your local voltage. Blown fuses should only be 

replaced by fuses of the same type and rating.

(35) 

Use the POWER switch to put your PMP2000 into operation. The POWER 

switch should always be in the “Off ” position when you are about to connect 

your unit to the mains.

(36) 

This is the RIGHT/MONO MAIN loudspeaker output of your PMP2000, 

where you can connect the right loudspeaker of a stereo system. For this 

purpose, switch  

(21)

  must be set to its upper position. If, however, you run 

a mono main mix (switch  

(21)

  set to its lower position), this loudspeaker 

output provides the main mix signal in mono.

(37) 

The BRIDGE loudspeaker output allows you to combine the left and 

right stereo channel in one mono output, which is useful for applications 

that require the use of one loudspeaker only. To use the BRIDGE output, 

switch  

(21)

  must be set to “LEFT/RIGHT”.

(38) 

This is the LEFT/MONITOR loudspeaker output of your PMP2000, to which 

you can connect the left loudspeaker of a stereo system (switch  

(21)

  set to 

its upper position). If you do a main mix in mono (switch  

(21)

  set to its lower 

position), this loudspeaker output provides the monitor signal in mono.

(39) 

SERIAL NUMBER.