Insignia NS-R5101 用户手册

Insignia NS-R5101 5.1 Surround Sound A/V Receiver

www.insignia-products.com

To display the receiver status:
•

Press the DISPLAY button during playback to 
view the receiver status.

Each time this button is pressed, the display 
mode changes as follows:

•

Surround Mode

•

Volume

•

Input source

To clean this receiver, wipe with a soft, dry cloth. 
If the surfaces are extremely dirty, use a soft 
cloth dipped in a soap and water solution or a 
weak detergent solution.
•

Never use alcohol, paint thinner, or benzine 
to clean this receiver.

•

Before using a chemically treated cloth, read 
the instructions that came with the cloth 
carefully.

If a problem occurs, use the following 
troubleshooting table before contacting Insignia.
If the problem persists, attempt to solve it by 
switching the receiver off and on again. If this 
fails to resolve the problem, contact Insignia. 
Under no circumstances should you attempt to 
repair the receiver yourself as this could void the 
warranty.

If the input source is EXTERNAL IN, the surround 
mode is not displayed.

No power

1 The AC power 

cord is 
disconnected.

2 Poor connection 

at AC wall outlet 
or the outlet is 
inactive.

1 Connect the cord 

securely.

2 Check the outlet 

using a lamp or 
another 
appliance.

No sound

1 The speaker 

cords are 
disconnected.

2 The master 

volume is 
adjusted too low.

3 The MUTE button 

on the remote 
control is pressed 
to ON.

4 Speakers are not 

switched on.

5 Incorrect 

selection of the 
input source.

6 Incorrect 

connections 
between the 
components.

1 Check the 

speaker 
connections.

2 Adjust the master 

volume.

3 Press the MUTE 

button to cancel 
the muting effect.

4 Press the 

SPEAKER 
button to ON.

5 Select the 

desired input 
source correctly.

6 Make 

connections 
correctly.

No sound 
from the 
surround 
speakers

1 Surround mode 

is switched off 
(stereo mode).

2 Master volume 

and surround 
level are too low.

3 A monaural 

source is used.

4 Surround 

speaker setting is 
“N”.

1 Select a surround 

mode.

2 Adjust master 

volume and 
surround level.

3 Select a stereo or 

surround source.

4 Select the 

desired surround 
speaker setting.

No sound 
from the 
center 
speaker

1 Surround mode 

is switched off 
(stereo mode).

2 Center speaker 

setting is “N”.

3 Master volume 

and center level 
are too low.

1 Select the 

desired surround.

2 Select the 

desired center 
speaker setting.

3 Adjust master 

volume and 
center level.

No sound 
from the 
subwoofer

1 Subwoofer 

setting is “N”.

2 Subwoofer 

volume is too low.

3 Subwoofer is not 

working.

4 Subwoofer 

frequency set too 
low.

1 Set the 

subwoofer setting 
to ‘Y’.

2 Adjust the 

subwoofer 
volume.

3 Use the built-in 

test tone to test 
the speakers.

4 Set the 

subwoofer 
frequency to its 
highest limit.

Stations 
cannot be 
received

1 No antenna is 

connected.

2 The desired 

station frequency 
is not tuned in.

3 The antenna is in 

wrong position.

1 Connect an 

antenna.

2 Tune in the 

desired station 
frequency.

3 Move the 

antenna and retry 
tuning.

Preset 
stations 
cannot be 
received

1 An incorrect 

station frequency 
has been 
memorized.

2 The memorized 

stations are 
cleared.

1 Memorize the 

correct station 
frequency.

2 Memorize the 

stations again.