Bosch Appliances Security Camera PT-400 用户手册
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
and Screens
EN | 38
Bosch Security Systems | 6/12 | 38947D
No Restriction: This selection
typically is left at this setting at
all times. The output is not
restricted by an individual
transponder.
typically is left at this setting at
all times. The output is not
restricted by an individual
transponder.
Only From Transponder Selected: The
selected events are only output if
they were reported from the
transponder selected in the
Transponder Restriction above.
selected events are only output if
they were reported from the
transponder selected in the
Transponder Restriction above.
All from Transponder Selected: All
events are reported from the
transponder selected in the
Transponder Restriction above. The
selected events are reported from
all other transponders in the
system.
events are reported from the
transponder selected in the
Transponder Restriction above. The
selected events are reported from
all other transponders in the
system.
Alarms
Outputs the information about an alarm
including location, but not the
transponder and receiver levels. This
is the data typically sent to a
printer.
Points, Reporting Alarm
Outputs the transponder and receiver
levels for an alarm. Typically, this is
the data too detailed to send to a
printer and is used for diagnostics,
not normal system operation.
Tests, Single Line
Outputs the simple information about a
test. Typically, this is the data
normally sent to a printer.
Tests Including Point Info
Outputs the transponder and receiver
levels for a test. This is the data
usually too detailed to send to a
printer and is used for diagnostics,
not normal system operation. If this
option is selected, Test, Single Line
above, would not be selected for the
same output device.
Transmitter Low Battery
Outputs low battery reports received
from transmitters.
Operator Activity Log
Outputs all other operator activity
(audit trail) not covered by specific
event selections.
Preferences Changes
Outputs all changes made to system
preference selections.
Database Backup and Restore
Records all database backup and restore
activity.
Outputs the information about an alarm
including location, but not the
transponder and receiver levels. This
is the data typically sent to a
printer.
Points, Reporting Alarm
Outputs the transponder and receiver
levels for an alarm. Typically, this is
the data too detailed to send to a
printer and is used for diagnostics,
not normal system operation.
Tests, Single Line
Outputs the simple information about a
test. Typically, this is the data
normally sent to a printer.
Tests Including Point Info
Outputs the transponder and receiver
levels for a test. This is the data
usually too detailed to send to a
printer and is used for diagnostics,
not normal system operation. If this
option is selected, Test, Single Line
above, would not be selected for the
same output device.
Transmitter Low Battery
Outputs low battery reports received
from transmitters.
Operator Activity Log
Outputs all other operator activity
(audit trail) not covered by specific
event selections.
Preferences Changes
Outputs all changes made to system
preference selections.
Database Backup and Restore
Records all database backup and restore
activity.
Operator Database Changes
Records all changes to the operator
database.
Subscriber Database Changes
Records all changes to the subscriber
database.
Transponder Database Changes
Records all changes to the transponder
database.
Spare 2
Not currently implemented. Leave
unchecked.
Report Database Changes
Records all changes to the Alarm Report
Database.
Communications Failure
Records all communication failures and
restorals.
Transponder Communication
Records all communications to
transponders. This selection is only
used for engineering diagnostics.
Leaving this item selected generates a
significant amount of history and fills
up the hard disk drive quickly. Leave
this item unchecked.
Supervision Monitor
Reports changes in the supervision
status for all transmitters that are
being supervised.
RF Point Troubles
Outputs all troubles reported by RF
points. Check this item to monitor
problems with RF points.
Transponder Maps
Outputs all transponder status maps.
This selection is only used for
diagnostics. Leave this item unchecked.
Receive Level Maps
Outputs all maintenance alarm receive
level maps. This selection is only used
for diagnostics. Leave this item
unchecked.
Database Errors
Outputs all reported database errors.
This item is checked.
Transponder Troubles
Outputs all reported transponder
troubles. This item is checked for
devices used to monitor problems.
Records all changes to the operator
database.
Subscriber Database Changes
Records all changes to the subscriber
database.
Transponder Database Changes
Records all changes to the transponder
database.
Spare 2
Not currently implemented. Leave
unchecked.
Report Database Changes
Records all changes to the Alarm Report
Database.
Communications Failure
Records all communication failures and
restorals.
Transponder Communication
Records all communications to
transponders. This selection is only
used for engineering diagnostics.
Leaving this item selected generates a
significant amount of history and fills
up the hard disk drive quickly. Leave
this item unchecked.
Supervision Monitor
Reports changes in the supervision
status for all transmitters that are
being supervised.
RF Point Troubles
Outputs all troubles reported by RF
points. Check this item to monitor
problems with RF points.
Transponder Maps
Outputs all transponder status maps.
This selection is only used for
diagnostics. Leave this item unchecked.
Receive Level Maps
Outputs all maintenance alarm receive
level maps. This selection is only used
for diagnostics. Leave this item
unchecked.
Database Errors
Outputs all reported database errors.
This item is checked.
Transponder Troubles
Outputs all reported transponder
troubles. This item is checked for
devices used to monitor problems.