Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 4.0
System Operations
22 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
2. Enter the number of the zone to isolate and press
[STAY].
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
as you press [STAY]. All other Burglary Zones
are automatically isolated only after the system is
armed.
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
as you press [STAY]. All other Burglary Zones
are automatically isolated only after the system is
armed.
3. Repeat Step 2 for each zone you want to isolate.
As each zone is selected to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the selected zones continue to
flash until the next time the system is disarmed.
disarmed state.
The indicators for the selected zones continue to
flash until the next time the system is disarmed.
Example
To manually isolate zones 1, 3, and 4, press:
[STAY][STAY][1][STAY][3][STAY][4][STAY]
[AWAY]
[AWAY]
4.11.2 Code to Isolate
The code to isolate method permits only those User
Code holders with a priority level that includes Code
to Isolate. The standard isolating method is disabled
for any User Code with this priority level.
1. Press [STAY].
2. Enter your code and press [STAY].
Code holders with a priority level that includes Code
to Isolate. The standard isolating method is disabled
for any User Code with this priority level.
1. Press [STAY].
2. Enter your code and press [STAY].
Three beeps sound and the STAY indicator
flashes.
If you attempt to enter Isolating Mode with a
User Code that is not set for Code to Isolate, the
system ignores the attempt.
flashes.
If you attempt to enter Isolating Mode with a
User Code that is not set for Code to Isolate, the
system ignores the attempt.
3. Enter the number of the zone to isolate and press
[STAY].
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
you press [STAY]. All other burglary zones are
automatically isolated only after the system is
armed.
The indicator for the zone flashes.
24-Hour zones are automatically isolated as soon
you press [STAY]. All other burglary zones are
automatically isolated only after the system is
armed.
4. Repeat Step 3 for each zone to isolate.
As each zone is selected to isolate, the
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
corresponding zone indicator flashes. If
you make a mistake, enter the incorrect
zone number and press [STAY]. This
zone is no longer selected to isolate and
the zone indicator turns off.
5. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
disarmed state.
The indicators for the selected zones continue to
flash until the next time the system is disarmed.
flash until the next time the system is disarmed.
Example
To manually isolate zones 1, 3, and 4, press:
[STAY][User Code][STAY][1][STAY][3][STAY][4]
[STAY][AWAY]
[STAY][AWAY]
4.12 Fault
Analysis
Mode
Whenever a system fault occurs, the FAULT or
MAINS indicator flashes and the codepad beeps once
per minute.
MAINS indicator flashes and the codepad beeps once
per minute.
If the MAINS indicator flashes, the AC MAINS
supply is disconnected from the control panel. Refer
to AC MAINS Failure on page 24.
supply is disconnected from the control panel. Refer
to AC MAINS Failure on page 24.
To enter Fault Analysis Mode to determine a system
fault other than the AC MAINS supply:
1. Press and hold [5] until two beeps sound.
fault other than the AC MAINS supply:
1. Press and hold [5] until two beeps sound.
The FAULT indicator remains lit and the STAY
and AWAY indicators flash.
The lit zone indicators indicate the type of fault
that occurred. Refer to Table 14.
and AWAY indicators flash.
The lit zone indicators indicate the type of fault
that occurred. Refer to Table 14.
2. To exit from the Fault Analysis Mode, press
[AWAY].
The STAY and AWAY indicators turn off and
the FAULT indicator remains lit.
The STAY and AWAY indicators turn off and
the FAULT indicator remains lit.
Table 14:
Fault Indicators
Indicator Fault
Description
1
Low battery
2 Date
and
time
3
Sensor watch
4 Horn
speaker
disconnected
5
Telephone line fault
6 EEPROM
fail
7
AUX Power Supply fail
8 Communications
failure
4.13 Fault
Descriptions
1 – Low Battery
A low battery fault occurs when the battery supply
voltage falls below 11.2 VDC or when a Dynamic
Battery Test detects a low capacity battery. This fault
clears after a successful Dynamic Battery Test. The
system performs a Dynamic Battery Test every 4
hours after power is connected to the control panel
and every time the system is armed.
voltage falls below 11.2 VDC or when a Dynamic
Battery Test detects a low capacity battery. This fault
clears after a successful Dynamic Battery Test. The
system performs a Dynamic Battery Test every 4
hours after power is connected to the control panel
and every time the system is armed.
When reporting to the base station receiver, the
control panel sends a Battery Test Failure Report
(Contact ID Event Code 309) to indicate the low
battery fault.
control panel sends a Battery Test Failure Report
(Contact ID Event Code 309) to indicate the low
battery fault.