Bosch Appliances Home Security System ICP-CC404 用户手册
ICP-CC404 | Installation Guide | 15.0 System Reporting Information
Bosch Security Systems, Inc. | 12/08 | F01U089401-02
61
Location 332 (Section 15.5 Zone Status Reporting Options
on page 61) is ignored when programming the Alarm
Restore code and is global for all zones. A zone
Restore Report is sent only to the receiving party to
which the zone is allocated (for example, Receiver 1
or Receiver 2).
on page 61) is ignored when programming the Alarm
Restore code and is global for all zones. A zone
Restore Report is sent only to the receiving party to
which the zone is allocated (for example, Receiver 1
or Receiver 2).
15.5 Zone Status Reporting Options
Use
Location 332 to select whether Zone Status
Reports are sent to Receiver 1 (the default),
Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or there is no reporting at all. Table 46 lists the
reporting options.
Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or there is no reporting at all. Table 46 lists the
reporting options.
Table 46:
Zone Status Reporting Options
Option Description
0
No report required
1 Receiver
1
2
Receiver 2
4
Receiver 1 and Receiver 2
8
Receiver 2 only when Receiver 1 fails
15.6 Open/Close
Reports
Program the Open Report value in
Location 333 (the
default value is
11) and the Close Report value in
Location 334 (default 12).
An Opening Report (Contact ID Event Code 401) is
sent to the base station receiver when the system is
disarmed from AWAY Mode. A Closing Report
(Contact ID Event Code 401) is sent at the end of
Exit Time when the system is armed in AWAY
Mode.
sent to the base station receiver when the system is
disarmed from AWAY Mode. A Closing Report
(Contact ID Event Code 401) is sent at the end of
Exit Time when the system is armed in AWAY
Mode.
If an expanded format is selected, this code is used as
the Expansion Code and the user number that armed
or disarmed the system follows in the same
transmission.
the Expansion Code and the user number that armed
or disarmed the system follows in the same
transmission.
To enable Open and Close Reports in STAY Mode,
select Option 2 in Location 178 (refer to Section 12.2
Dialer Options 2 on page 50). To enable Open and
Close Reports only after a previous alarm, select
Option 1 in Location 178.
select Option 2 in Location 178 (refer to Section 12.2
Dialer Options 2 on page 50). To enable Open and
Close Reports only after a previous alarm, select
Option 1 in Location 178.
If Open and Close Reports are not
required, program Locations 333 and
334 as 0.
required, program Locations 333 and
334 as 0.
15.7 Open/Close
Reporting
Options
Use
Location 335 to select whether Zone Status
Reports are sent to Receiver 1 (the default),
Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or there is no reporting at all. Table 47 lists the
reporting options.
Receiver 2, or both, Receiver 2 only when Receiver 1
fails, or there is no reporting at all. Table 47 lists the
reporting options.
Table 47:
Open/Close Reporting Options
Option Description
0
No Open/Close Reports required
1 Receiver
1
2
Receiver 2
4
Receiver 1 and Receiver 2
8
Receiver 2 only when Receiver 1 fails
15.8 Codepad Duress Report
Program the Codepad Duress Report value in
Location 336.
Location 336.
The default value is
6.
A Duress Report (Contact ID Event Code 121) is sent
to the base station receiver when a user adds 9 to the
end of any valid User Code used to disarm the
system. This alarm is always silent. A Duress Alarm
can be activated during Exit Time (in other words, if
the system is armed and then disarmed with a 9 at the
end of the User Code before Exit Time expires, a
Duress Report is sent). Adding 9 to the end of a User
Code when arming the system does not cause a
Duress Alarm.
to the base station receiver when a user adds 9 to the
end of any valid User Code used to disarm the
system. This alarm is always silent. A Duress Alarm
can be activated during Exit Time (in other words, if
the system is armed and then disarmed with a 9 at the
end of the User Code before Exit Time expires, a
Duress Report is sent). Adding 9 to the end of a User
Code when arming the system does not cause a
Duress Alarm.
If you want a 3 to activate a Codepad Duress Alarm
instead of 9, select Option 2 in Location 430 (refer to
Section 18.7 Consumer Options 3 on page 75).
instead of 9, select Option 2 in Location 430 (refer to
Section 18.7 Consumer Options 3 on page 75).
Restore Reports are not sent for this
event.
event.
If Duress Reports are not required,
program Location 336 as 0.
program Location 336 as 0.
15.9 Codepad Panic Report
Program the Codepad Panic Report value in
Location 337 (tens digit) and Location 338 (units
digit).
Location 337 (tens digit) and Location 338 (units
digit).
The default values are
7 (tens) and 15 (units).
A Panic Alarm Report (Contact ID Event Code 120)
is sent to the base station receiver when a user presses
either [1] and [3] or [STAY] and [AWAY] at the same
time. A Panic Alarm is audible, but you can program
the alarm as silent by selecting Option 1 in Location
425 (refer to Section 18.2 System Options 2 on page 73).
is sent to the base station receiver when a user presses
either [1] and [3] or [STAY] and [AWAY] at the same
time. A Panic Alarm is audible, but you can program
the alarm as silent by selecting Option 1 in Location
425 (refer to Section 18.2 System Options 2 on page 73).
Restore Reports are not sent for this
event.
event.
If Panic Reports are not required,
program Locations 337 and 338 as 0.
program Locations 337 and 338 as 0.
15.10 Codepad Fire Report
Program the Codepad Fire Report value in
Location
339 (tens digit) and Location 340 (units digit).
The default values are
7 (tens) and 14 (units).