Gaggenau AL400721 产品宣传册
106
Vario cooktops
V K 414 110
Stainless steel
Width 38 cm
Width 38 cm
Included in the price
1 cooking insert
1 glass
1 glass
cover
1 hand
grip
1 residuary
filter
1 water drain valve
Installation accessories
A G 050 000
A G 050 000
Drain installation set with check valve
drain set (DN 40) and connecting
sleeve (½'' on 1½'')
drain set (DN 40) and connecting
sleeve (½'' on 1½'')
A G 060 000
Drain installation set enables drainage
of cooking liquid into a suitable
receptacle
of cooking liquid into a suitable
receptacle
V A 420 010
Connection strip for combination with
other Vario appliances of the 400
series for surface installation
other Vario appliances of the 400
series for surface installation
V A 420 011
Connection strip for combination with
other Vario appliances of the 400
series for surface installation with
appliance cover/adjustment strip
other Vario appliances of the 400
series for surface installation with
appliance cover/adjustment strip
V A 420 000
Connection strip for combination with
other Vario appliances of the 400
series for flush installation
other Vario appliances of the 400
series for flush installation
V A 420 001
Connection strip for combination with
other Vario appliances of the 400
series for flush installation with
appliance cover/adjustment strip
other Vario appliances of the 400
series for flush installation with
appliance cover/adjustment strip
V A 440 010
Stainless steel appliance cover with
mounting strip
mounting strip
V A 450 400
Stainless steel adjustment strip 38 cm
Required accessory for combination of
several Vario appliances of the 400
series with at least one appliance cover
to compensate the appliance depth.
Required accessory for combination of
several Vario appliances of the 400
series with at least one appliance cover
to compensate the appliance depth.
Special accessories
F K 023 000
F K 023 000
Pasta basket
G E 020 010
Unperforated cooking insert
G E 020 020
Perforated cooking insert
Vario steamer 400 series
V K 414
– Steaming in cooktop size
– Exact water temperature control
from 45 °C to 95 °C
– Cooking on two levels, without
flavour transfer
– Solid stainless steel control knob
– Precision crafting of 3 mm stainless
steel
– For surface installation with a
visible edge or for flush installation
– Can be combined perfectly with
other Vario appliances of the 400
series
series
Cooking zones
Water capacity 1 to 6 litres.
Handling
Control knobs with illuminated ring,
temperature markings and outlet water.
Electronic water temperature control
from 45 °C to 95 °C, in 5 °C steps.
temperature markings and outlet water.
Electronic water temperature control
from 45 °C to 95 °C, in 5 °C steps.
Features
Steam cooking level with electronic
steam control for pressureless
cooking.
Automatic boiling point detection.
Motor-driven 1/2” water drain valve.
steam control for pressureless
cooking.
Automatic boiling point detection.
Motor-driven 1/2” water drain valve.
Safety
Safety shut-off.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
If installing with the appliance cover
VA 440 or adjustement strip VA 450
take into account the additional space
required for the depth.
If combining several appliances with at
least one appliance cover, the
adjustment strip VA 450 is required to
compensate for the depth of the
appliance without the appliance cover.
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
In the cut-out, the installation system
requires the side edge to be at least
10 mm for surface installation and at
least 13 mm for flush installation.
Ensure a continuous cut surface of
90°.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush installa-
tion:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop manu-
facturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
If installing with the appliance cover
VA 440 or adjustement strip VA 450
take into account the additional space
required for the depth.
If combining several appliances with at
least one appliance cover, the
adjustment strip VA 450 is required to
compensate for the depth of the
appliance without the appliance cover.
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
In the cut-out, the installation system
requires the side edge to be at least
10 mm for surface installation and at
least 13 mm for flush installation.
Ensure a continuous cut surface of
90°.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush installa-
tion:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop manu-
facturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
Please read additional planning notes
on page 116–123 .
on page 116–123 .
If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Built-in control panel to be integrated
in the bottom cabinet at drawer level.
Panel thickness 16 – 26 mm.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 26 mm thick (there must be
a recess at the rear).
Seal the worktop cutout.
VK 414 and VF 414 must not be
installed directly next to each other.
A minimum lateral clearance of at least
40 mm from adjacent heat-sensitive
furniture.
In case of suspended cabinets a
ventilation hood must be installed
above the steamer.
If a cover is fitted, the glass lid must be
removed when closing it.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 16 kg.
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Built-in control panel to be integrated
in the bottom cabinet at drawer level.
Panel thickness 16 – 26 mm.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 26 mm thick (there must be
a recess at the rear).
Seal the worktop cutout.
VK 414 and VF 414 must not be
installed directly next to each other.
A minimum lateral clearance of at least
40 mm from adjacent heat-sensitive
furniture.
In case of suspended cabinets a
ventilation hood must be installed
above the steamer.
If a cover is fitted, the glass lid must be
removed when closing it.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 16 kg.
Connection
Total connected load 2.0 kW.
Plan a connection cable.
Plan a connection cable.