Rangemaster U109100 - 02 用户手册
15
After the appliance is installed, ensure that the
water tube is properly arranged to avoid indents
or damage.
This appliance is installed with an MSEH10
icemaker.
Installation of the icemaker must be carried out
by an authorised agent.
This icemaker can only be supplied with drinking
water.
water tube is properly arranged to avoid indents
or damage.
This appliance is installed with an MSEH10
icemaker.
Installation of the icemaker must be carried out
by an authorised agent.
This icemaker can only be supplied with drinking
water.
3 Operating the icemaker
8 ice cubes are made in every cycle. The ice
making capacity depends on freezer temperature,
ambient temperature and appliance door opening
frequency. Ensure that the icemaker switch is set to
position “OFF” before the appliance is connected
to water supply, and to position “ON” after the
appliance is connected to the water supply.
ambient temperature and appliance door opening
frequency. Ensure that the icemaker switch is set to
position “OFF” before the appliance is connected
to water supply, and to position “ON” after the
appliance is connected to the water supply.
Water will be supplied when the set temperature
of the icemaker is reached.
Caution: Allow 24 hours after the appliance
is installed before the freezer compartment
temperature drops down to the degree for ice
making.
temperature drops down to the degree for ice
making.
Do not use the fi rst loads of ice cubes after
installation or after the appliance has been turned
off for an extended period.
off for an extended period.
Some of the 8 ice cubes dropped from the
icemaker in one cycle may stick to each other.
4 Set the icemaker control to position
“OFF” when any of the following
events occur.
Water supply is interrupted for hours.
Ice cube bin is removed for an extended period.
Holidays - turn off the water supply to the unit.
Ice cube bin is removed for an extended period.
Holidays - turn off the water supply to the unit.
NOTE! - The Icemaker ON/Off lever will switch
the Icemaker Off when the container is full of ice,
and will have to be switched on manually, before
any further ice will be produced.
and will have to be switched on manually, before
any further ice will be produced.
5 If this is your first icemaker,
Some strange sounds may be heard in the process
of ice making.
•
•
•
•
•
•
•
•
•
6 If ice cubes are stored for an
extended period
Ice cubes stored for an extended period may
become opaque or generate a strange odour. The
ice cube bin should be cleaned regularly with warm
water. The ice cube bin should be cooled down and
air-dried before replacement to avoid sticking of ice
cubes to the tray.
ice cube bin should be cleaned regularly with warm
water. The ice cube bin should be cooled down and
air-dried before replacement to avoid sticking of ice
cubes to the tray.
7 Extended disuse of the ice cube bin
in the winter
If the ice cube bin is not used for an extended
period in winter, remove all the ice cubes from
the tray and wash the tray clean with warm water.
Wipe the tray with a towel before replacing it to
the appliance, and then turn off the valve between
water supply and the appliance.
the tray and wash the tray clean with warm water.
Wipe the tray with a towel before replacing it to
the appliance, and then turn off the valve between
water supply and the appliance.
Removing and installing the ice
cube bin
cube bin
Removing the ice cube bin
Push back at the top of the ice cube bin, lift at the
front and pull it forward to remove it from the side
supports.
supports.
Replacing the ice cube bin
Slide the ice cube bin back into the side runners
and push it back into position.
When replacing the
bin, be sure to press
it fi rmly into place. If
it does not go all the
way back, remove it
and rotate the drive
mechanism 90°, then
push the bin back
again until the clips fi t
in position.
it fi rmly into place. If
it does not go all the
way back, remove it
and rotate the drive
mechanism 90°, then
push the bin back
again until the clips fi t
in position.
ON
OFF
ICEMAKER