Vermont Casting DVT38S2 用户手册
32
Chateau™ Decorative Gas Appliance
20009543
Fuel Conversion Instructions
WARNING! This conversion kit shall be installed
by a qualified service agency in accordance with
the manufacturer’s instructions and all applicable
codes and requirements of the authority having
jurisdiction. If the information in these instructions
is not followed exactly, a fire, explosion or pro-
duction of carbon monoxide may result causing
property damage, personal injury or loss of life.
The qualified service agency is responsible for the
proper installation of this kit. The installation is
not proper and complete until the operation of the
converted appliance is checked as specified in the
manufacturer’s instructions supplied with the kit.
CAUTION: The gas supply shall be shut off prior to
disconnecting the electrical power, before pro-
ceeding with the conversion.
by a qualified service agency in accordance with
the manufacturer’s instructions and all applicable
codes and requirements of the authority having
jurisdiction. If the information in these instructions
is not followed exactly, a fire, explosion or pro-
duction of carbon monoxide may result causing
property damage, personal injury or loss of life.
The qualified service agency is responsible for the
proper installation of this kit. The installation is
not proper and complete until the operation of the
converted appliance is checked as specified in the
manufacturer’s instructions supplied with the kit.
CAUTION: The gas supply shall be shut off prior to
disconnecting the electrical power, before pro-
ceeding with the conversion.
Avertissement: Cette trousse de conversion
Ne doit être installée que par le représentant d’un
organisme qualifié et conformément aux instruc-
tions du fabricant et aux codes et exigences
pertinentes de l’autorité compétente. Quiconque
ne respecte pas à la lettre les instrucitons du
présent guide risque de déclencher un incendie,
une explosion ou le dégagement de monoxyde de
carbone entraînant des dommages matériels, des
lésions corporelles ou la perte de vies humaines.
L’organisme qualifié qui effectur les travaux est
responsible de l’installation de cette trousse.
L’installation n’est pas terminée tant que le fonc-
tionnement de l’appareil converti n’a pas été vérifié
selon la notice du fabricant qui accompagne la
trousse.
Ne doit être installée que par le représentant d’un
organisme qualifié et conformément aux instruc-
tions du fabricant et aux codes et exigences
pertinentes de l’autorité compétente. Quiconque
ne respecte pas à la lettre les instrucitons du
présent guide risque de déclencher un incendie,
une explosion ou le dégagement de monoxyde de
carbone entraînant des dommages matériels, des
lésions corporelles ou la perte de vies humaines.
L’organisme qualifié qui effectur les travaux est
responsible de l’installation de cette trousse.
L’installation n’est pas terminée tant que le fonc-
tionnement de l’appareil converti n’a pas été vérifié
selon la notice du fabricant qui accompagne la
trousse.
ATTENTION: Avant d’effectuer la conversin, coupez
d’abord l’limentation en gaz, ensuite, coupez
l’alimentation électrique.
d’abord l’limentation en gaz, ensuite, coupez
l’alimentation électrique.
Conversion Precautions
Allow unit to cool if it has been operating.
Before proceeding with conversion, turn control knob on
valve to OFF and turn gas supply OFF. Turn OFF any
electricity that may be going to appliance.
Before proceeding with conversion, turn control knob on
valve to OFF and turn gas supply OFF. Turn OFF any
electricity that may be going to appliance.
Conversion Procedure
1. Remove glass frame. Refer to Glass Frame Assembly
section on Page 22.
2. Remove lava rock, volcanic rock, embers and logs.
CAUTION: Logs may be hot.
3. With a Phillips or Robertson screwdriver, remove the
four (4) screws holding the fettle to the burner assem-
blies. With a 3/8” hex head, remove the two (2) hex
blies. With a 3/8” hex head, remove the two (2) hex
nuts holding each burner tube assembly to the base
pan assembly on both sides. Remove the burner tube
assemblies.
pan assembly on both sides. Remove the burner tube
assemblies.
4. Remove two (2) hex nuts holding the left burner leg.
Remove burner leg. (Fig. 58)
CO105a
gas conversion
Pilot
1/28/00 djt
Pilot Hood
Pilot
Bracket
CO105a
Fig. 59 Remove pilot hood.
CO106a
DV360/580
Gas Conversion
Pilot2
1/28/00 djt
Index Tab
Allen Wrench
Snap Ring
CO106a
Fig. 60 Remove pilot orifice.
5. Slide the burner housing assembly to the left and
away.
6. Replace the four (4) injectors. Refer to Table 1.
7. Replace pilot orifice.
8. Remove pilot hood by lifting up. (Fig. 59) NOTE: It is
7. Replace pilot orifice.
8. Remove pilot hood by lifting up. (Fig. 59) NOTE: It is
not necessary to remove the pilot tube for conversion.
9. Remove pilot orifice with 5/32” Allen wrench. (Fig. 60)
�����
��������
����
��������
����
KT550
Fig. 58 Use 3/8” socket to remove hex nuts holding burner
legs.
legs.
Hex
Nuts