Chamberlain WD832KD 1/2 HP 用户手册
25
INSTALLATION STEP 12
Connect Door Arm to Trolley
Follow instructions which apply to your door type as
illustrated below and on the following page.
illustrated below and on the following page.
SECTIONAL DOORS ONLY
•
•
Make sure garage door is fully closed. Pull the
emergency release handle to disconnect the outer
trolley from the inner trolley. Slide the outer trolley back
(away from the pulley) about 8" (20 cm) as shown in
Figures 1, 2 and 3.
emergency release handle to disconnect the outer
trolley from the inner trolley. Slide the outer trolley back
(away from the pulley) about 8" (20 cm) as shown in
Figures 1, 2 and 3.
• Figure 1:
– Fasten straight door arm section to outer trolley with
– Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
ring fastener.
– Fasten curved section to the door bracket in the
same way, using the 5/16"x1-1/4" clevis pin.
IMPORTANT: The groove on the straight door arm
MUST face away from the curved door arm (Figure 4).
• Figure 2:
– Bring arm sections together. Find two pairs of holes
MUST face away from the curved door arm (Figure 4).
• Figure 2:
– Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far
apart as possible to increase door arm rigidity.
apart as possible to increase door arm rigidity.
• Figure 3, Hole alignment alternative:
– If holes in curved arm are above holes in straight
– If holes in curved arm are above holes in straight
arm, disconnect straight arm. Cut about 6" (15 cm)
from the solid end. Reconnect to trolley with cut end
down as shown.
from the solid end. Reconnect to trolley with cut end
down as shown.
– Bring arm sections together.
– Find two pairs of holes that line up and join with
– Find two pairs of holes that line up and join with
bolts, lock washers and nuts.
•
Pull the emergency release handle toward the opener
at a 45° angle so that the trolley release arm is
horizontal. Proceed to Adjustment Step 1, page 27.
Trolley will re-engage automatically when opener is
operated.
at a 45° angle so that the trolley release arm is
horizontal. Proceed to Adjustment Step 1, page 27.
Trolley will re-engage automatically when opener is
operated.
Trolley
Stop Bolt
Stop Bolt
Ring
Fastener
Fastener
Door
Bracket
Bracket
Straight
Door Arm
Door Arm
Curved Door Arm
Inner
Trolley
Trolley
Outer
Trolley
Trolley
Emergency
Release
Handle
Release
Handle
Clevis Pin
5/16"x1"
5/16"x1"
Clevis Pin 5/16"x1-1/4"
Pulley
8" (20 cm) min.
Trolley
Stop Bolt
Stop Bolt
Lock
Washers
5/16"
Washers
5/16"
Nuts
5/16"-18
5/16"-18
Door Bracket
Bolts
5/16"-18x7/8"
5/16"-18x7/8"
Pulley
8" (20 cm) min.
Trolley
Stop Bolt
Stop Bolt
Cut this end
Lock
Washers
5/16"
Washers
5/16"
Nuts
5/16"-18
Bolts
5/16"-18x7/8"
5/16"-18x7/8"
Pulley
8" (20 cm) min.
Figure 1
Figure 2
Figure 3
Lock Washer 5/16"
Nut 5/16"-18
Ring Fastener
Hex Bolt
5/16"-18x7/8"
5/16"-18x7/8"
Clevis Pin
5/16"x1" (Trolley)
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
5/16"x1-1/4" (Door Bracket)
HARDWARE SHOWN ACTUAL SIZE
Figure 4
Straight
Door Arm
Door Arm
Curved
Door Arm
Door Arm
(Groove
facing out)
facing out)
Straight
Door Arm
Door Arm
Curved
Door
Arm
Door
Arm
CORRECT
INCORRECT