Bosch MVM-BVRM 用户手册
The Recording preferences page is displayed for each encoder. This page only appears if a
device is assigned to a VRM system.
Note: When you configure the automatic recording mode, you cannot configure any settings
here.
VRM Settings tab, 26
device is assigned to a VRM system.
Note: When you configure the automatic recording mode, you cannot configure any settings
here.
VRM Settings tab, 26
Mode
Select the required option.
–
Select the required option.
–
All
The VRM system discovers all available and configured iSCSI targets and assigns the
available capacity automatically. If a target fails or memory capacity is used, another
target is selected automatically. In this case, you cannot enter targets on the tab.
The VRM system discovers all available and configured iSCSI targets and assigns the
available capacity automatically. If a target fails or memory capacity is used, another
target is selected automatically. In this case, you cannot enter targets on the tab.
–
Restricted
Recordings are stored primarily to the targets entered here. Primary target and secondary
target are used equivalently.
If no disk space is available on either of the targets entered, other storage blocks of the
VRM system are used until there is space available again on the entered targets.
Recordings are stored primarily to the targets entered here. Primary target and secondary
target are used equivalently.
If no disk space is available on either of the targets entered, other storage blocks of the
VRM system are used until there is space available again on the entered targets.
–
Failover
Recordings are saved only to primary target. If it is not possible to save to this target, the
recording will be saved to the target entered under secondary target.
A failure situation is reached if the primary target does not provide storage blocks due to
whatever reason: system down, network error, no capacity left.
You can leave the second list empty. In this case no failover is possible but the number of
required iSCSI sessions is reduced.
Recordings are saved only to primary target. If it is not possible to save to this target, the
recording will be saved to the target entered under secondary target.
A failure situation is reached if the primary target does not provide storage blocks due to
whatever reason: system down, network error, no capacity left.
You can leave the second list empty. In this case no failover is possible but the number of
required iSCSI sessions is reduced.
–
Preferred
Recordings are saved to the entered targets in the specified sequence. For this, enter
both a primary and a secondary target. The secondary target is only used while the
primary target has no storage capacity available.
Only if these targets are not available, the recordings will be distributed across other
targets.
Recordings are saved to the entered targets in the specified sequence. For this, enter
both a primary and a secondary target. The secondary target is only used while the
primary target has no storage capacity available.
Only if these targets are not available, the recordings will be distributed across other
targets.
Primary target
Select the entry for the required target, if you have selected a setting other than All under
Mode.
Select the entry for the required target, if you have selected a setting other than All under
Mode.
Secondary target
Select the entry for the required target if you have selected Failover under Mode. If you have
set Restricted, Failover, or Preferred, entering a secondary target is optional. Restricted and
Preferred without a second target are identical.
Select the entry for the required target if you have selected Failover under Mode. If you have
set Restricted, Failover, or Preferred, entering a secondary target is optional. Restricted and
Preferred without a second target are identical.
Retention time tab
Main window > Cameras tab > Select a camera
Note: If the Cameras tab is not displayed, enable it:
Enabling the Cameras tab, 13
You can specify the retention time for recordings for each camera:
Note: If the Cameras tab is not displayed, enable it:
Enabling the Cameras tab, 13
You can specify the retention time for recordings for each camera:
Maximum retention time (days)
Recordings are automatically deleted as soon as this value and the minimum retention time
are exceeded.
The maximum retention time is valid also for already existing recordings.
The value O means infinite. In this case VRM Server tries to keep the recordings according to
the minimum retention time, for example 10 days. But if enough storage is available, older
recordings can exist, for example 20 or more days.
Recordings are automatically deleted as soon as this value and the minimum retention time
are exceeded.
The maximum retention time is valid also for already existing recordings.
The value O means infinite. In this case VRM Server tries to keep the recordings according to
the minimum retention time, for example 10 days. But if enough storage is available, older
recordings can exist, for example 20 or more days.
12.12
Video Recording Manager
User interface | en
33
Bosch Sicherheitssysteme GmbH
Software Manual
2012.05 | v1 | DOC