Toshiba DK40I 用户手册
Toll Restriction
Program *45-2 (1~6) – LCR/Toll Restriction Bypass
4-24
Strata DK Programming 5/00
Program *45-2 (1~6) – LCR/Toll Restriction Bypass
for Special Numbers that Do Not Begin with */#
for Special Numbers that Do Not Begin with */#
Processor Type:
DK14, DK40i, all RCTUs and BCUs
Program Type:
Toll Restriction
Initialized Default:
All data blank
Program *45-2 Overview
Use this program to allow special CO Area Codes and Centrex feature access codes or extension
numbers to bypass toll restriction and route over the local LCR route - if using LCR. (Toll
Restriction is always applied after dialing the special numbers assigned to this table.
numbers to bypass toll restriction and route over the local LCR route - if using LCR. (Toll
Restriction is always applied after dialing the special numbers assigned to this table.
Codes programmed in this table will bypass Toll Restriction, and will be sent to the CO local route
if using LCR. Calls subject to toll restriction are normally restricted if “*” or “#” is pressed during
toll restriction digit analysis. However, in some special applications (e.g., the Strata DK System is
connected behind a PBX/Centrex, or assume_9 Centrex dialing), “*” and/or “#” may be required
within the first four digits or the last digit.
if using LCR. Calls subject to toll restriction are normally restricted if “*” or “#” is pressed during
toll restriction digit analysis. However, in some special applications (e.g., the Strata DK System is
connected behind a PBX/Centrex, or assume_9 Centrex dialing), “*” and/or “#” may be required
within the first four digits or the last digit.
If the digit string containing */# matches with any of the six programmed digit strings of this
program, toll restriction is applied after the matched digit string. This program can also be used for
special area code dialing plans where the digit “1” is not dialed before the area code. See example
on the Program *45-2 Examples.
program, toll restriction is applied after the matched digit string. This program can also be used for
special area code dialing plans where the digit “1” is not dialed before the area code. See example
on the Program *45-2 Examples.
Notes
●
If using LCR behind Centrex, enter the Centrex trunk access code (such as “9” entered in the
example below). If “9” is entered in this table, the user must dial 9 + 9 + 911 for an emergency
call when using LCR.
example below). If “9” is entered in this table, the user must dial 9 + 9 + 911 for an emergency
call when using LCR.
●
The record sheet above allows up to 5-digit numbers. If the number to be entered is less than 5
digits, enter Blanks (Button 01) for all digits less than 5 digits.
digits, enter Blanks (Button 01) for all digits less than 5 digits.
Example (Centrex assume 9)
If using LCR behind “assume 9” Centrex, and restricted stations (1+AC not allowed) must dial
12XX# and 13XX# as Centrex station numbers (# is the Centrex end-of-dialing code for extension
numbers) enter
12XX# and 13XX# as Centrex station numbers (# is the Centrex end-of-dialing code for extension
numbers) enter
+
+
%XWWRQ
+
%XWWRQ
+
and
+
+
%XWWRQ
+
%XWWRQ
+
as data in Programs *45-21 and *45-22, respectively.
✱ ✱ ✱ ✱ 6SNU ✱ +ROG 6SNU
+ROG 6SNU +ROG 6SNU +ROG
SELECT = 2
SELECT = 1~6
DATA = 1~5 Digit Code
(that are not subject to toll restriction)
(that are not subject to toll restriction)
First Digit:
0~9 only
Non-first Digits:
0~9,
✱,
#
When editing:
•
Press LED Button 01 to delete or leave a blank.
•
Press LED Button 02 to allow all digits to work.
SELECT =
DATA = 1~5 Digits
1
2
3
4
5
6