Teledyne 200AH 用户手册

 

Operating Modes 

NO/NO

x

 switching mode, NO only 

mode, NO

x

 only mode. 

Paramagnetic Sensor 

Ranges 

In 1 ppm increments from 5 ppm to 
5000 ppm; Single range, independent 
ranges or autoranging 

In 1 % increments from 5 % to 
100%,  Independent of NO

X

 range 

Noise at zero 

<0.020 ppm RMS 

0.05% O

2

 

Noise at span 

<0.5% of reading RMS above 20 ppm 

<0.1% O

2

 

Detection Limit (Note 1) 

0.040 ppm  

0.1% O

2

 

Zero Drift (Note 2) 

<0.5% full scale/24 hours 

0.1% O

2

 

Zero Drift (Note 2) 

<1.0% full scale/7 days 

0.1% O

2

 

Span Drift (Note 2) 

<1% FS/24 hours 

0.1% O

2

 

Lag Time 

 

- Switching Mode 

- 20 sec (Note 3) 

- NO

x

 mode 

- 4 sec (Note 3) 

< 4sec 

Response Time 

 

- Switching Mode 

- 95% in < 40 sec (Note 3) 

- NO

x

 mode 

- 95% in < 10 sec (Note 3) 

95% in <10 sec 

Sample Flow Rate (Analyzer) 

370 cc/min 

10% (Including bypass) 

 

Sample Flow Rate (Sensors) 

40 cc/min 

10%  

80 cc/min 

10%  

Linearity 

1% of full scale 

0.1% O

2

 

Precision 

0.5% of reading 

0.1% O

2

 

Temperature Range 

5-40

C 

Humidity 

0-95% RH non-condensing 

Temp Coefficient 

< 0.1% per 

C 

< 0.1% per 

C 

Voltage Coefficient 

< 0.1% per V 

< 0.1% per V 

Dimensions HxWxD 

7"x17"x23.6" (18 cm x 43 cm x 61 cm) 

Weight, Analyzer 

45 lbs (22 kg) 

Weight, Pump Pack 

16 lbs (7 kg) 

Power, Analyzer 

100 V~ 50/60 Hz, 120 V~ 60 Hz, 220 V~ 50 Hz, 240 V~ 50 Hz, 200 watts 

Power, Analyzer

4

 

230 V~ 50 Hz, 2.5A 

Power, Ext Pump 

110 V~ 60 Hz, 220 V~ 50 Hz, 240 V~ 50 Hz, 295 watts 

Power, Ext Pump

4

 

230 V~ 50 Hz, 2.5A 

Environmental 

Installation Category (Over-voltage Category) II 

 

Pollution Degree 2 

Analog Resolution 

1 part in 2048 of selected voltage or 
current range 

1 part in 2048 of selected voltage or 
current range 

Recorder Output 

0-100mV, 0-1, 5, 10v, bipolar 

0-100mV, 0-1, 5, 10v, bipolar 

Current Loop Option 

4-20ma isolated 

4-20ma isolated 

Status 

12 Status Outputs from opto-isolator 

Measurement Units 

ppm, mg/m

3

 % 

1. 

Defined as twice the zero noise level. 

2. 

At constant temperature and voltage. 

3. 

Lag & response times longer for external converter option. 

4. 

Electrical ratings for CE Mark compliance.