Premier Mounts XUF-1330L Merkblatt

Seite von 2
 
INSTALLATION GUIDE: XUF-1330L
 
 
Victory LCD Wall Mounting System 
 
The Victory LCD Mounting System is designed for secure installation of LCD displays of up to 
40 lbs. in weight. 
 
 
 
Warning Statements
 
 
WARNING:
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM 
WEIGHT  OF  40  LBS.  IF  NOT,  THE  WALL MUST BE REINFORCED. PROPER 
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN 
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO 
COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH. 
WARNING:
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION 
OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION 
PROCEDURE TO PREVENT PERSONAL INJURY. 
WARNING:
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS 
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION 
INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY 
DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE 
LOCATION FOR FUTURE  REFERENCE. 
 
A secure structure must support the weight or load of the display. When mounting to a wall that 
contains wooden studs, dead center of the wooden stud must be confirmed prior to installation. 
 
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to 
do so could result in damage to the display and/or damage to the mounting surface. 
 
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct 
heat energy. Failure to do so may result in damage to the display and could increase the risk of 
fire. 
 
At least two qualified people should perform the installation procedure. Injury and/or damage 
can result from dropping or mishandling the display. 
 
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be 
installed on any surface other than wooden studs, use suitable hardware (which is 
commercially available). 
 
Contact Victory Mounts with any technical / installation questions. 
 
 
 
 
 
 
Included Hardware
 
 
 
¾” Spacer (Qty 4) 
 
 
M4 x 12mm Phillips 
Head Screw  
(Qty 4) 
 
2” Wood Screw  
(Qty 2) 
 
M4 x 30mm Phillips 
Head Screw  
(Qty 4) 
 
Bubble Level (Qty 1) 
 
 
 
Tool List 
Phillips/ Slot Head Screw Driver 
Electronic Stud Finder 
Allen Wrench (Supplied) 
Portable Drill 
¼” Masonry Bit for Concrete Installation 
 
NOTE:  The included level may be permanently attached 
 
to the wall plate by inserting the level into the 
 
receptacle on the back of the wall plate. 
Wood Stud Installation 
NOTE:  Using a wood stud finder, locate the   stud  centers 
 
behind the wall. Once found, make a pencil 
 
marking on the center of the wood studs. Once the 
 
mark is made, it is strongly recommended that a 
 
pilot hole be drilled with a 1/8” drill bit. 
1. Place the back plate against the wall with the hook 
 
towards the bottom.  
2.  Secure the back plate using one (1) 2” wood screw. 
3. Using the integrated bubble guide, carefully adjust the 
 
back plate until it is level.  
4.  Attach the remaining 2” wood screw into the back plate 
 and 
tighten. 
 
 
Concrete Installation 
NOTE: ¼” x 2 ¼” Threshold anchors must be 
 
used for concrete installation. They can be 
 
purchased at your local hardware  
store. 
1. Place the back plate against the wall with the hook 
 
towards the bottom.  
2.  Level and mark with a pencil the two mounting points 
 
found on the back plate.  
3. Next, drill two holes using an electric drill and ¼” 
 
masonry bit.  
4.  Insert the threshold anchors into the holes  that 
were
 
  
drilled in the wall.  
NOTE:  If necessary, use a hammer to lightly tap each 
 
  anchor into place so that they are flush with the 
 
  wall. Once mounted in the wall, unscrew the    
 
  slotted cap off of the threshold screw. 
5.  Once the anchors are in place, set the back plate back 
 
over the concrete anchors.  
6.  Using a Slot Head screw driver, attach the  back  plate  by 
 
threading the two slotted caps onto the threaded insert 
 
that is recessed into the wall.  
7. Make sure all screws are snug, but be careful 
 
not to over-tighten them.
 
 
 
 
 
Slotted Cap Threaded 
Insert 
Threshold Anchor 
Threshold 
Anchor