Panasonic AG-3200P Benutzerhandbuch

— 12 —

Page 12

June 5, 2002 1:41 pm

Up to 8 timer recording programs can be made using VCR Plus+ 
timer programing, Express timer programing or 24HR Quick 
Programing method as far as a year in advance. Remember, the 
clock must be set before you can program the timer.

● If all the 8 programs have already been set, “PROGRAM FULL” 

● After timer recording is completed, the VCR turns off 

● You can program the timer recording while a regular recording 

● Even if a power failure occurs, the VCR keeps your timer 

● If the tape reaches its end during timer recording, the recording 

#

䡬

” and “ $” on the display panel blink. Press 

TIMER to disengage timer, then press STOP/EJECT (0) on 
the VCR to eject the cassette or press POWER 1 then press 
REW (3) on the Remote to rewind the tape.

The VCR Plus+ programing system assigns a VCR Plus+ guide 
channel to the TV channels and the cable channels. These guide 
channel numbers are also called the VCR Plus+ channel codes. 
Most TV listings have a section, usually a chart, indicating the 
guide channel numbers assigned to each station.
To ensure that VCR Plus+ timer recording operates correctly, it is 
necessary to set the VCR Plus+ “Guide Channel Set” for each 
station.
If you have moved to a different area or if a broadcasting station’s 
channel number has been changed, perform the following steps to 
set the correct guide channel number.

A

Press MENU on the Remote. Press 

rt

 to move the highlight bar 

(arrow) to “INITIAL SET”, then press OK or 

e

.

B

Press 

rt

 to move the highlight bar (arrow) to “GUIDE 

CHANNEL SET”, then press OK or 

e

.

C

Press 

rt

 or the Number keys to select the 

VCR Plus+ guide channel number as 
shown in the TV listing, then press OK or 

e

.

D

Press 

rt

 or the Number keys to select the 

number of the channel on which the guide 
channel’s broadcasts are received, then 
press OK or 

e

.

● Repeat steps 

3

3

3

3

 and 

4

4

4

4

 for each instance.

E

Press MENU on the Remote.

The PlusCode programing numbers are 
the numbers next to the program in 
most TV listing.
Load a cassette with the record safety 
tab intact. The VCR turns on, and the 
counter is reset, automatically.

A

Press PROG. on the Remote to access 
the PlusCode No. screen.

B

Press the appropriate Number keys 
to input the PlusCode number, then 
press OK or 

e

. Check to make sure 

the setting is accurate on the Program screen.

● If the Guide Channel Set screen 

appears after pressing OK, press the 
Number keys, CH+/– or 

rt

 to input 

the number of the channel on which 
the broadcast for the PlusCode 
number is received on the VCR.

● To set the tape speed, press SP/EP.

● To change the stop time, press STOP+/–.

● To timer-record daily (Monday–Friday) or weekly serials, 

press DAILY (M-F) (Number key “8”) or WEEKLY (Number 
key “9”). Pressing the button again makes the “DAILY” or 
“WEEKLY” display disappear.

● If you made a mistake, press CANCEL to access the PlusCode 

No. screen again.

● If an incorrect PlusCode number or the one for a broadcast 

already finished has been inputted, “ERROR” is displayed for 
about 5 seconds, then the PlusCode No. screen reappears.

C

Press OK or PROG..

● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” 

appears, see “Program overlap warning display” (

墌

pg. 13).

D

Press TIMER. The VCR turns off automatically and “

#

” is 

displayed on the display panel.

Load a cassette with the record safety tab intact. The VCR turns 
on, and the counter is reset, automatically.

A

Press PROG. on the Remote to access the PlusCode No. screen.

B

Press START+/– once to access 
Program screen.
Press START+/–, STOP+/–, DATE+/– or 
CH+/– repeatedly to enter the start 
time, stop time, date or channel.

● Press and hold START+/– or STOP+/– 

to increase the time in 30-minute 
intervals.

● To set the tape speed, press SP/EP.

● To timer-record daily (Monday–Friday) or weekly serials, 

press DAILY (M-F) (Number key “8”) or WEEKLY (Number 
key “9”). Pressing the button again makes the “DAILY” or 
“WEEKLY” display disappear.

C

Press OK or PROG..

● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” 

appears, see “Program overlap warning display” (

墌

pg. 13).

AG-3200P-EN.fm  Page 12  Wednesday, June 5, 2002  1:43 PM