Toshiba D-VR17KB Benutzerhandbuch

35

EN

The error number appears on the Timer Programming 
list. 

The error programme will be displayed in grey 
with an error number.

E1–E22, 
E37–E39: Recording error
E23–E24: Unrecordable disc
E25

: • Copy prohibited programme

• Cannot record because of the NTSC / 

PAL-60 signal is received.

E26–E28: Copy prohibited programme
E29

: Disc protected

E30

: Disc full

E31

: Already recorded 99 titles (Video 

mode)

E32

: Already recorded 99 titles (VR mode)

E33

: Already recorded 999 chapters

E34

: No space for Control Information

E35

: PCA (Power Calibration Area) full

E36

: Already finalised Video format disc

E40

: • There are some unrecorded parts due 

the overlapped timer programmes.

• Recording did not start at the start 

time.

• There is no tape in the cassette 

compartment.

• Tape recording reaches to the tape 

end during timer recording.

E41

: Power failure

E42

: No disc

E43

: Already 49 titles recorded (+VR mode)

E44

: Already 254 chapters recorded (+VR mode)

E45

: Copy prohibited programme

E46

: It is impossible to record additionally on 

a disc recorded by other units when 
setting “Make Recording Compatible” 
to “OFF”. (+VR mode)

The error programme will be deleted once you 
check the error in the programme list, or once you 
cancel the timer-standby mode and re-enter it.

• If there is a power failure or the unit is unplugged for 

more than 30 seconds, the clock setting and all 
timer settings will be lost.

• If there is no disc or an unrecordable disc in the tray  

(finalised DVD-RW/-R, finalised DVD+R, a fully 
recorded disc, etc.), the DVD on the front panel 
display will flash and the timer recording will not 
occur. Insert a recordable disc.

• If there is no tape or a tape with a record tab is not in 

the cassette compartment, the VCR on the front 
panel display will flash and the timer recording 
cannot be performed. Please insert a recordable 
tape.

• When all timer recordings are complete, the 

  

icon flashes. To play back or eject the recorded disc, 
press [TIMER SET], and then press [PLAY 

P] or 

[OPEN / CLOSE 

O].

• The timer recording cannot be performed in DVD 

and VCR at the same time. If you set two 
programmings with the same channel and time both 
in DVD and VCR, the programming that has priority 
will be recorded.

• You cannot make any DVD operation during DVD 

timer recording.

• You cannot make any VCR operation during VCR 

timer recording.

• If the Start and End times are same, the length of 

the recording will be set for 24 hours. If the disc or 
tape becomes full during recording, the unit will turn 
itself off. To continue recording, press [TIMER SET] 
to cancel the timer-standby mode, insert a 
recordable disc or tape and press [TIMER SET] 
again.

• When 2 or more programmes are overlapped, 

“Timer program overlapped” appears, and the 
overlapped programme will be displayed in blue. To 
correct the timer programme refer to “Checking, 
Cancelling or Correcting the Timer Programming 
Information” on page 34.

• If the Start time is earlier and the End time is later 

than the current time, the recording will start 
immediately after you press [TIMER SET].

• If a videotape ends during the timer recording, the 

unit will automatically stop, eject the videotape, and 
turn itself off. To continue recording, insert a 
recordable tape.

Priority of overlapped settings
The unit records programmes according to priority if 
the timer programmes overlap.

If the starting time is same:
• The timer programming set first (PROG. 1) has 

priority.

When the starting time and the ending time for 
each programmes are different:
• A programme that has earlier start time has priority.

PROG. 2 
recording 
will start 
after 
PROG. 1 
recording is
completed.

The first 2 minutes (at the longest) will be cut off.

The first 2 minutes (at the longest) will be cut off.

E9GA0BD_EN.book  Page 35  Monday, March 26, 2007  10:25 AM