Invacare Ranger X Benutzerhandbuch
24
3. Refer back to the starting procedure to complete the
desired change.
Installing
1. Position NEW standard seat frame subassembly on
seat mount plates.
2. Secure NEW standard seat frame subassembly onto
seat mounting plates with the existing four (4) mount-
ing screws, locknuts and spacers, if applicable. Torque
to 156-inch pounds.
3. Refer back to the starting procedure to complete the
desired change.
CHANGING SEAT DEPTH
Standard Seat Frame
NOTE: Review the chart below. This will determine the
components needed to obtain the desired seat depth.
B. If the desired change only requires a NEW seat
pan, refer to REMOVING/INSTALLING SEAT PAN
in this procedure of the manual.
C. For all other seat depth changes, perform the fol-
lowing:
l PREPARATIONS FOR REMOVING/IN-
l PREPARATIONS FOR REMOVING/IN-
STALLING SEAT FRAME (STANDARD
FRAME, ADJUSTABLE FRAME, AND CAP-
TAINS VAN SEAT) in this procedure of the
manual.
Perform one (1), two (2), or all three (3) of the pro-
cedures listed below depending on the compo-
nents required for the desired seat depth deter-
mined from STEPS 1-5:
l REMOVING/INSTALLING CJ BACK BRACK-
l REMOVING/INSTALLING CJ BACK BRACK-
ETS in this procedure of the manual.
l REMOVING/INSTALLING STANDARD SEAT
SUBASSEMBLY in this procedure of the
manual.
l REMOVING/INSTALLING SEAT PAN in this
procedure of the manual.
After completing the procedure(s) listed above, per-
form the steps outlined in PREPARATIONS FOR
REMOVING/INSTALLING SEAT FRAME (STAN-
DARD FRAME, ADJUSTABLE FRAME, AND
CAPTAINS VAN SEAT) to complete the desired
seat depth change.
Adjustable Seat Frame (FIGURE 3)
NOTE: Review the chart below. This will determine the com-
ponents needed to obtain your desired seat depth.
SEAT FRAME COMPONENTS
CJ BACK
SEAT
SEAT BRACKETS
SEAT
FRAME
DEPTH REQUIRED
PAN
DEPTH
12-inches
to
YES
17-inch
16-inch deep
15-inches
16-inches
NO
16-inch
16-inch deep
17-inches
NO
17-inch
16-inch deep
18-inches
NO
18-inch
18-inch deep
19-inches
NO
19-inch
18-inch deep
20-inches
NO
20-inch
20-inch deep
21-inches
NO
21-inch
20-inch deep
22-inches
NO
22-inch
22-inch deep
COMPONENT IDENTIFICATION TABLE
FOR STANDARD SEAT FRAME
1. Find current seat depth in left hand column in the chart.
2. Follow that row to right under seat frame components.
3. Verify and note the components of the current seat depth.
4. Repeat STEPS 1-3 for your desired seat depth.
5. Compare existing components of the current seat depth
2. Follow that row to right under seat frame components.
3. Verify and note the components of the current seat depth.
4. Repeat STEPS 1-3 for your desired seat depth.
5. Compare existing components of the current seat depth
and the required components for the desired seat depth.
6. Perform one (1) of the following:
A. If the current seat depth and the desired seat depth
is within the 12-15-inch seat depth range, this change
can be accomplished by repositioning the back
canes on the CJ back brackets. Refer to CHANG-
ING SEAT DEPTH BETWEEN 12-15-INCHES in
this procedure of the manual.
NOTE: Note the four (4) different lengths of side frames
short, medium, long, and X-long, as well as the two differ-
ent center frames, short and long. These components are
interchanged to obtain the various different seat depths.
SEAT FRAME COMPONENTS
CJ BACK
SEAT BRACKETS SEAT
SIDE CENTER
DEPTH REQUIRED PAN
FRAME FRAME
12-inches
to
YES
17-inch
Short
Short
15-inches
16-inches
NO
16-inch
Short
Short
17-inches
NO
17-inch
Short
Short
18-inches
NO
18-inch Medium Short
19-inches
NO
19-inch Medium Short
20-inches
NO
20-inch
Long
Long
21-inches
NO
21-inch
Long
Long
22-inches
NO
22-inch X-Long
Long
COMPONENT IDENTIFICATION TABLE
FOR STANDARD SEAT FRAME
PROCEDURE 6
SEAT FRAME
S
E
A
T
F
F
R
A
M
E