Socket Mobile CHS 7XRx, 20pcs CX2844-1161 Merkblatt
Produktcode
CX2844-1161
Quick Start Guide
Bluetooth
®
Cordless Hand Scanner
(CHS)
7X and 7XRx
7X SKU# CX2849-1242 (P/N 8550-00036)
7XRx SKU# CX2843-1160 (P/N 8550-00047)
7XRx SKU# CX2843-1160 (P/N 8550-00047)
© 2010 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, Socket Bluetooth Cordless Hand Scanner, and Business
Mobility Now! are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark is a registered trademark
of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and trade names contained
herein may be those of their respective owners.
Mobility Now! are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark is a registered trademark
of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and trade names contained
herein may be those of their respective owners.
Assembling the AC Adapter:
The included AC adapter comes with four plugs.
Find the correct plug for your region and slide it
into the head of the adapter.
Charging the CHS:
The CHS must be fully charged before first use.
Total charging time from empty to full is about
3.5 hours. The LED of the CHS will be red while
charging, and green when fully charged.
The included AC adapter comes with four plugs.
Find the correct plug for your region and slide it
into the head of the adapter.
Charging the CHS:
The CHS must be fully charged before first use.
Total charging time from empty to full is about
3.5 hours. The LED of the CHS will be red while
charging, and green when fully charged.
WARNING! Do not remove the factory-
installed battery!
installed battery!
Attaching the Tether:
Use a coin or screwdriver to turn the lock under
the CHS. Remove the battery cover and wrap
the string loop of the tether around the inside
part of the lock. Replace the battery cover. If
desired, attach the tether to a lanyard/belt.
Use a coin or screwdriver to turn the lock under
the CHS. Remove the battery cover and wrap
the string loop of the tether around the inside
part of the lock. Replace the battery cover. If
desired, attach the tether to a lanyard/belt.
Touch Screen Stylus:
Use the stylus tip on Pocket PC and other device
touch screens. Do not use the stylus if damaged,
as it may scratch the screen. The stylus does not
work on tablets with Active Matrix displays.
Use the stylus tip on Pocket PC and other device
touch screens. Do not use the stylus if damaged,
as it may scratch the screen. The stylus does not
work on tablets with Active Matrix displays.
Optional Charging Accessories: Available separately.
http://www.socketmobile.com/products/bluetooth-barcode-
scanners/accessories/
scanners/accessories/
Charging Cradle
AC4026-708
AC4026-708
Charging Cradle,
Antimicrobial
AC4050-1152
Antimicrobial
AC4050-1152
USB to DC Plug
Charging Cable
AC4051-1192
Charging Cable
AC4051-1192
Mobile Power
Pack (not sold in
EMEA)
AC4050-1152
Pack (not sold in
EMEA)
AC4050-1152
Package Contents
• Socket Bluetooth Cordless Hand Scanner (CHS) 7X or 7XRx
• Lanyard / belt clip with retractable tether
• Rechargeable battery (pre-installed, DO NOT REMOVE)
• Charging cable
• Socket Bluetooth Cordless Hand Scanner (CHS) 7X or 7XRx
• Lanyard / belt clip with retractable tether
• Rechargeable battery (pre-installed, DO NOT REMOVE)
• Charging cable
Basic Functionality
Note: No software is required for normal operation.
Note: No software is required for normal operation.
Function Procedure
Powering on
/off
/off
Power On: Press and hold down the power button
until you hear two (low-high) tones.
until you hear two (low-high) tones.
Power Off: Press and hold down the power button
until you hear two (high-low) tones.
until you hear two (high-low) tones.
Scanning
barcodes
barcodes
Press and hold the trigger button to activate the
scanner. An aiming beam will appear for 3 seconds.
Position the red aiming beam over the 2D (or 1D)
barcode. The CHS will beep, flash a green LED, and
vibrate to confirm the barcode data was decoded and
recorded in your application. Refer to User’s Guide for
more details.
scanner. An aiming beam will appear for 3 seconds.
Position the red aiming beam over the 2D (or 1D)
barcode. The CHS will beep, flash a green LED, and
vibrate to confirm the barcode data was decoded and
recorded in your application. Refer to User’s Guide for
more details.
Enabling/
Disabling
Symbologies
Disabling
Symbologies
Please refer to the Command Sheet in the User’s
Guide, available online at:
Guide, available online at:
http://www.socketmobile.com/support/downloads
LED
Trigger
button
button
Power button
Disconnecting
Disconnect through your device’s Bluetooth software
or simply turn off the CHS.
or simply turn off the CHS.
Factory Reset
Reverts CHS back to factory default state. You can do
this to remove a pairing or revert to the default
Bluetooth device (keyboard for Windows, “other” for
iPad).
1. Power on CHS
2. Press and hold down the Trigger button and
this to remove a pairing or revert to the default
Bluetooth device (keyboard for Windows, “other” for
iPad).
1. Power on CHS
2. Press and hold down the Trigger button and
momentarily press the Power button while still
holding down the Trigger button.
holding down the Trigger button.
3. After 15 seconds, the scanner will beep. Release
the Trigger button.
4. The scanner will beep 5 times and power off.
5. The next time you power on the scanner, it will
5. The next time you power on the scanner, it will
take longer than normal. After the scanner
finishes powering on, it will have factory default
settings.
finishes powering on, it will have factory default
settings.
Pairing Reset
Releases the Bluetooth pairing from the last system
the CHS was paired to. This allows new pairing to
another system.
1. Power on CHS
2. Press and hold down the Trigger button and press
the CHS was paired to. This allows new pairing to
another system.
1. Power on CHS
2. Press and hold down the Trigger button and press
the Power button until you hear a series of 3
tones.
tones.
LED
LED LED
Behavior
Meaning
1 blink per second
Bluetooth radio is on, but not
connected
connected
Bluetooth
Status
(Blue)
Status
(Blue)
1 blink per 3 seconds
Scanner connected to computer
On
Data successfully scanned and
transmitted to host device
transmitted to host device
Good
Read
(Green)
Read
(Green)
On when connected
to charging source
to charging source
Scanner is fully charged
1 blink per second
20% battery capacity remaining
On when connected
to charging source
to charging source
Battery Charging (on cradle or
AC power)
AC power)
Battery
Status
(Red)
Status
(Red)
Off
Powered off or Good Battery
status
status
Beeps
Beep Patterns
Meaning
2 beeps (low-high)
Power on
2 beeps (high-low)
Power off
1 beep
Scanner connected to computer. When
connected, the scanner will auto power off
after 2 hours of inactivity.
connected, the scanner will auto power off
after 2 hours of inactivity.
2 beeps (same tone)
Scanner disconnected from computer. When
disconnected, the scanner will auto power off
after 5 minutes of inactivity.
disconnected, the scanner will auto power off
after 5 minutes of inactivity.
2 long beeps (same
tone)
tone)
Scanner unsuccessfully tried 10 times to connect
to computer. After these attempts, the scanner
will go into sleep mode and power off after 5
minutes of inactivity.
to computer. After these attempts, the scanner
will go into sleep mode and power off after 5
minutes of inactivity.
1 beep with green
LED
LED
Data successfully scanned and sent to
computer.
computer.
5 consecutive tones
The scanner detects an internal fault and will
reset itself. If the scanner is connected to a host
computer, it will disconnect during the reset.
reset itself. If the scanner is connected to a host
computer, it will disconnect during the reset.
6/2010
Printed in USA