Gemini MP-3000X Benutzerhandbuch

(2)

VOLTAGE SELECTOR: To set the proper voltage, adjust the VOLTAGE SELECTOR (1) switch to 115 or 230 volts.

POWER JACK (AC IN): Connect the power plug into the POWER JACK (2) for power.

REMOTE CONTROL: Use the included CABLE & REMOTE CONTROL (3) jacks to connect the REMOTE CONTROL

to the MAIN UNIT.

LINE OUTPUT JACKS: LINE OUTPUT JACKS (4) provide stereo sound via RCA cables to your mixer or receiver.

NOTE

MAKE SURE CABLES ARE PLUGGED IN TIGHT FOR OPTIMAL SOUND.

BNC (DIGITAL OUTPUT): Use the BNC (5) jack to connect to any type of device that accepts digital signals.

POWER: Press the POWER (6) button to turn on the CD player.

NOTE

MAKE SURE VOLTAGE SELECTOR SWITCH (1) IS SET BEFORE USE.

DISC TRAY:

Put a CD in the DISC TRAY (7) after pressing OPEN/CLOSE (8); trays hold both 12 cm and 8 cm CDs.

OPEN/CLOSE: Tap OPEN/CLOSE (8) once to open the tray and again to close it.

DISPLAY: The DISPLAY (9) shows the various functions for the CD Player. See

FUNCTION DESCRIPTIONS for

details.

PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (10) shows the TIME ELAPSED and TIME REMAINING

PLAY/PAUSE: Press PLAY/PAUSE (11) button to activate PLAY or PAUSE mode. See

CUE or ROBO START

INSTRUCTIONS for details.

CUE/PREVIEW: Tap CUE/PREVIEW (12) to come back to a set CUE or press and hold to PREVIEW from a CUE,

refer to

CUE INSTRUCTIONS.

SEARCH: Use the SEARCH (13) buttons to scan forward and reverse directions on a TRACK

TRACK SEARCH:

Press the TRACK SEARCH (14) buttons to select which TRACK to play.

TIME: Tap the TIME (15) button to switch the TIME preference in three modes: ELAPSED, REMAIN, TOTAL REMAIN.

STOP: Press STOP (16) once to stop the CD.

SINGLE AUTO CUE/CONTINUE: Tap SINGLE AUTO CUE/CONTINUE (17) for:

SINGLE AUTO CUE, CONTINUOUS,

and NORMAL

modes.

FLY CUE: FLY CUE (18) sets a CUE POINT on the fly.

B/EXIT: Press B/EXIT (19) in PLAY mode, after a CUE POINT is memorized to start a LOOP, press again to exit LOOP.

B-EDIT: Press B-EDIT (20) and use the JOG WHEEL (22) to edit an existing LOOP, press again to exit EDIT mode.

RETURN: To play from a saved CUE POINT or a LOOP, press RETURN (21) to play the LOOP or the CUE

again.

JOG WHEEL: The JOG WHEEL (22) has various functions: PITCH BEND, CUEING, and TRACK SEARCHING.

SEARCH MODE: Press to change the SEARCH MODE (23) of the JOG WHEEL (22) from MUSIC to TRACK mode.

SEARCH MODE LED: The SEARCH MODE LED (24) displays which SEARCH MODE (23) is in use.

PITCH: The PITCH (25) button activates the PITCH CONTROL SLIDE (27)

PITCH BEND: Buttons for PITCH BEND (26), lower or raise the pitch percentage (- or +) 4% when pressed.

PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (27) up or down will lower or raise the pitch

percentage (- or +) 4%, 8%, & 16%.

VPS (VARIABLE PITCH SELECTOR) 4%, 8% & 16%: Use the VPS (28) buttons use to change the PITCH settings
from 4%, 8%, & 16%.

ROBO START: Using ROBO START (29) enables you to alternate play between two CDs using both sides.

QUICK START GUIDE: