Westcott 4835 Merkblatt
Light Modifiers
Page 1 of 2
Questions? Please call 800.886.1689 or email
info@fjwestcott.com
.
©F.J. Westcott Company
Setup Instructions
Soft Boxes
Style Series: 4805, 4830, 4831, 4832, 4833, 4834, 4835, 4836
Description
The Westcott Box comes with a fabric shell with either a white or silver interior. Both boxes have an
internal baffle, exterior diffusion panel, four support rods and a storage bag. The flaps in the back are
made of flame-retardant material to withstand heat up to 1000 watts and have hook and loop tape tab
closures. If overheating is a concern, the Box’s unique design allows heat to escape by opening the flaps
in the back of the unit or opening the 2 (tent style) heat vents.
Product Contains
Description
The Westcott Box comes with a fabric shell with either a white or silver interior. Both boxes have an
internal baffle, exterior diffusion panel, four support rods and a storage bag. The flaps in the back are
made of flame-retardant material to withstand heat up to 1000 watts and have hook and loop tape tab
closures. If overheating is a concern, the Box’s unique design allows heat to escape by opening the flaps
in the back of the unit or opening the 2 (tent style) heat vents.
Product Contains
[1] Soft Box
[4] Assembly Rods
[1]
[4] Assembly Rods
[1]
Inner
Baffle
[1] Outer Diffusion Panel
[1] Carry Case
[1] Carry Case
INSTRUCTIONS
To assemble the Westcott Box, a speed ring must be used (the Westcott Spiderlite& Spiderlite TD5 is an
exception as the rod holes are built into the light head). The speed ring needed to mount the Box is the model of
speed ring that fits the particular light that is used. After the Westcott Box has been mounted onto the speed ring,
fasten the speed ring onto the light. Westcott Boxes may also be mounted onto other speed rings on the market.
To mount the speed ring onto the Westcott Box, insert the support rods into the rod sleeves in the corner of the
fabric shell of the Box all the way into the end of the pockets. Before putting on the exterior diffusion panel,
place the Box onto a table or the floor and spread rods apart so the Box is rectangular in shape. Insert one rod into
the hole marked R1 of the speed ring. While pressing down on the speed ring, insert the next rod into hole R3.
The pressure exerted on the speed ring should be enough to bring the speed ring down to easily guide the next rod
into place. Bend the rod directly beside the second one to coincide with the angle of the hole R2 in the speed ring.
(You should be inserting the rods in the direction of a figure eight, ending with the rod that was directly beside the
first rod inserted). Slide the remaining rod end into the hole marked R4 of the speed ring. **Note that all rods
must be seated completely into the holes of the ring.
After the Westcott Box is mounted onto the speed ring, mount the Box and speed ring onto the light stand. The
internal baffle may now be snapped into place. DO NOT USE THE INNER BAFFLE WITH A BULB OVER
500 WATTS. 500-WATT BULB CAN BE USED WITH BAFFLE IN BOXES MEDIUM SIZE OR LARGER
ONLY.
Next, the external diffuser may be fastened onto the front of the unit. The external diffusion panel can be used in
either the recessed or flat front positions. The speed ring should also allow the Westcott Box to turn from a long
profile to a wide profile even after it is mounted on the light.
exception as the rod holes are built into the light head). The speed ring needed to mount the Box is the model of
speed ring that fits the particular light that is used. After the Westcott Box has been mounted onto the speed ring,
fasten the speed ring onto the light. Westcott Boxes may also be mounted onto other speed rings on the market.
To mount the speed ring onto the Westcott Box, insert the support rods into the rod sleeves in the corner of the
fabric shell of the Box all the way into the end of the pockets. Before putting on the exterior diffusion panel,
place the Box onto a table or the floor and spread rods apart so the Box is rectangular in shape. Insert one rod into
the hole marked R1 of the speed ring. While pressing down on the speed ring, insert the next rod into hole R3.
The pressure exerted on the speed ring should be enough to bring the speed ring down to easily guide the next rod
into place. Bend the rod directly beside the second one to coincide with the angle of the hole R2 in the speed ring.
(You should be inserting the rods in the direction of a figure eight, ending with the rod that was directly beside the
first rod inserted). Slide the remaining rod end into the hole marked R4 of the speed ring. **Note that all rods
must be seated completely into the holes of the ring.
After the Westcott Box is mounted onto the speed ring, mount the Box and speed ring onto the light stand. The
internal baffle may now be snapped into place. DO NOT USE THE INNER BAFFLE WITH A BULB OVER
500 WATTS. 500-WATT BULB CAN BE USED WITH BAFFLE IN BOXES MEDIUM SIZE OR LARGER
ONLY.
Next, the external diffuser may be fastened onto the front of the unit. The external diffusion panel can be used in
either the recessed or flat front positions. The speed ring should also allow the Westcott Box to turn from a long
profile to a wide profile even after it is mounted on the light.