Panasonic AJ-SPX800E Benutzerhandbuch
100
8-4
VF
8-4-1
VF DISPLAY
8-4-2
VF MARKER
8-4-3
USER BOX
The ____ in the Adjustable Range column indicates the preset
mode.
mode.
Items/
Data Saved
Adjustable
Range
Remarks
DISP
CONDITION
CONDITION
NORMAL
HOLD
HOLD
NORMAL: Display status constantly.
HOLD:
HOLD:
Display status only when the
MODE CHECK switch is pressed.
MODE CHECK switch is pressed.
– C U F E
DISP MODE
1
2
3
2
3
Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
– C U F E
VF OUT
Y
NAM
R
G
B
NAM
R
G
B
Select the VF output.
Y:
Y:
Brightness signal
NAM: Output signal with the highest level
among R, G, and B signals.
R:
Rch signal
G:
Gch signal
B:
Bch signal
– C U F E
VF DTL
0
:
3
:
5
Select the VF DTL.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
– C U F E
ZEBRA1
DETECT
DETECT
0%
:
70%
:
109%
Set the ZEBRA1 detection level (IRE value).
– C U F E
ZEBRA2
DETECT
DETECT
0%
:
85%
:
109%
Set the ZEBRA2 detection level (IRE value).
– C U F E
ZEBRA2
ON
SPOT
OFF
SPOT
OFF
Set the ZEBRA2 to ON, OFF, or SPOT.
– C U F E
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
15%
20%
25%
30%
35%
Set the camera incoming light volume at
which to display LOW LIGNT.
which to display LOW LIGNT.
– C U F E
ECU MENU
DISP.
DISP.
ON
OFF
OFF
Set the menu display on the VF to ON or
OFF when the ECU is connected.
OFF when the ECU is connected.
– C U F E
50M
INDICATOR
INDICATOR
ON
OFF
OFF
Set the 50M recording indication to ON or
OFF.
OFF.
– C U F E
MARKER/CHAR
LVL
LVL
50%
60%
70%
80%
90%
100%
60%
70%
80%
90%
100%
Adjust the brightness of markers and
characters displayed on the VF.
characters displayed on the VF.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
TABLE
A
B
B
Select the VF MARKER setting table.
First, select table A or B, then set the items
below for each table.
First, select table A or B, then set the items
below for each table.
– C U F E
CENTER MARK OFF
1
2
3
4
2
3
4
Switch the centre mark.
OFF: Do not display centre mark.
1:
OFF: Do not display centre mark.
1:
+ (large)
2:
Hollow (large)
3:
+ (small)
4:
Hollow (small)
– C U F E
SAFETY ZONE OFF
1
2
2
Select the frame type for the safety zone.
OFF: Do not display frame.
1:
OFF: Do not display frame.
1:
Box
2:
Corner frame
– C U F E
SAFETY AREA 80%
:
90%
:
100%
Set the position of the safety zone.
– C U F E
FRAME SIG
4:3
13:9
14:9
VISTA
13:9
14:9
VISTA
Set the frame marker.
Only enabled when REC MODE is set to
16:9.
The VISTA ratio is 16:8.65.
Only enabled when REC MODE is set to
16:9.
The VISTA ratio is 16:8.65.
– C U F E
FRAME MARK ON
OFF
Set the frame marker to ON or OFF.
– C U F E
FRAME LVL
0
:
15
Set the level outside the frame marker.
0:
0:
Equivalent to signal OFF.
15:
Same brightness as centre area.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
USER BOX
ON
OFF
OFF
Select whether or not to display the USER
BOX.
BOX.
– C U F E
USER BOX
WIDTH
WIDTH
1
:
13
:
100
Set the width of the USER BOX.
– C U F E
USER BOX
HEIGHT
HEIGHT
1
:
13
:
144
Set the height of the USER BOX.
– C U F E
USER BOX H
POS
POS
–50
:
+00
:
+50
Set the horizontal position of the USER
BOX.
BOX.
– C U F E
USER BOX V
POS
POS
–144
:
+000
:
+144
Set the vertical position of the USER BOX.
– C U F E