Panasonic AJ-SPX800E Benutzerhandbuch
90
7-3-2
Error Codes
The following error codes are displayed in the display window if
an error occurs in the camera:
an error occurs in the camera:
5. P2 Card Fully Recorded
Display window
indication
indication
All 7 bar indicators for remaining MEDIA capacity
start blinking.
start blinking.
WARNING lamp
Continues to light up until an operation is
performed.
performed.
Tally lamp
Continues to blink 4 times per second until an
operation is performed.
operation is performed.
Viewfinder
The END indicator blinks.
Warning tone
Continues to beep until an operation is
performed.
performed.
Warning
description
description
The P2 cards are recorded to maximum capacity.
Recording/
playback operation
playback operation
The recording stops.
Countermeasures
Delete the clips in the P2 card or insert a new P2
card.
card.
8. Battery Nearly Empty
Display window
indication
indication
One of the bars in the battery remaining indicator
starts blinking.
starts blinking.
WARNING lamp
Blinks once per second.
Tally lamp
Blinks once per second.
Viewfinder
The BATT LED blinks.
Warning tone
Beeps 4 times per second.
Warning
description
description
The battery is about to run out.
Recording/
playback operation
playback operation
Continues to operate.
Countermeasures
Replace the battery as required.
6. Recording Error
Display window
indication
indication
“00:00:00:11” appears in the time code display
field.
field.
WARNING lamp
Blinks 4 times per second while recording
continues.
continues.
Tally lamp
Blinks 4 times per second while recording
continues.
continues.
Viewfinder
The REC WARNING indicator lights up.
Even after recording is stopped, this display
continues to light up until the next operation is
performed.
Even after recording is stopped, this display
continues to light up until the next operation is
performed.
Warning tone
Beeps 4 times per second while recording
continues.
continues.
Warning
description
description
Recording signal processing error.
Recording/
playback operation
playback operation
Recording stops.
Countermeasures
Restart recording. Or, turn the power OFF and
turn it ON again, before starting recording.
turn it ON again, before starting recording.
9. P2 Card Nearly Full
Display window
indication
indication
One of the bars for remaining MEDIA capacity
starts blinking.
starts blinking.
WARNING lamp
Blinks once per second while recording
continues.
continues.
Tally lamp
Blinks once per second while recording
continues.
continues.
Viewfinder
The P2 card remaining capacity indicator blinks.
Warning tone
Beeps once per second while recording
continues.
continues.
Warning
description
description
The total remaining capacity of all the P2 cards is
two minutes or less.
two minutes or less.
Recording/
playback operation
playback operation
Continues to operate.
Countermeasures
Replace the cards. If there is an empty card slot,
insert a new card.
insert a new card.
7. Low Wireless Signal Reception
Display window
indication
indication
No display.
WARNING lamp
Blinks 4 times per second. (During pause and
recording)
recording)
Tally lamp
Blinks 4 times per second while recording
continues.
continues.
Viewfinder
The WIRELESS RF indicator lights up while
recording continues.
recording continues.
Warning tone
Beeps 4 times per second while recording
continues.
continues.
Warning
description
description
This error indicates poor wireless audio reception
conditions.
conditions.
Recording/
playback operation
playback operation
Continues to operate without receiving the
wireless microphone signal.
wireless microphone signal.
Countermeasures
Check the microphone power supply and the
reception status of the wireless receiver.
reception status of the wireless receiver.
Code No.
Description
E-11
Video initialisation error
E-27
Recording control error
E-30
P2 card removal error
E-38
P2 streaming microcontroller error
E-3F
Microprocessor error in the camera control circuit.
E-6F
Reference signal error.