Panasonic AJ-HDX400E Benutzerhandbuch

85

ECU MENU DISP.

ON
OFF

For selecting ON or OFF for displaying the
MENU on the viewfinder when the ECU is
connected.

DISP CONDITION

NORMAL
HOLD

NORMAL: The statuses are displayed at all

times.

The statuses are displayed only
when the MODE CHECK switch is
pressed.

DISP MODE

1
2
3

For performing the DISP MODE setting.  This
item is used to select the camera’s warning or
message displays.  For details, refer to “4-7-4
Display modes and setting changes/
adjustment result messages.”

VF OUT

Y
NAM
R
G
B

For selecting the VF output.
Y:

Luminance signal

NAM: The signal with the highest level among

the R, G and B signals is output.

R channel signal

G channel signal

B channel signal

VF DTL

0

:

2

:

5

For performing the VF DTL selection.  This
item is used to further emphasize the DTL of
the VF signals.  If 0 is set, the DTL will be the
same as that of the main line signals.

ZEBRA1 DETECT

0%

:

70%

:

109%

For setting the ZEBRA1 detection level (IRE
level).

ZEBRA2 DETECT

0%

:

85%

:

109%

For setting the ZEBRA2 detection level (IRE
level).

ZEBRA2

ON
SPOT
OFF

For selecting ON or OFF for ZEBRA2 or
selecting SPOT.

LOW LIGHT LVL

OFF
10%
15%
20%
25%
30%
35%

For setting how much lower the camera’s
input light quantity should be in order for
“LOW LIGHT” to be displayed.

MARKER/
CHAR LVL

50%
60%
70%
80%
90%
100%

For setting the brightness of the markers and
characters displayed in the viewfinder.

The underlining in the variable range column indicates the setting in the preset mode.

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

DS.GAIN DISP

GAIN
FRM RATE

For selecting whether to display the DS.GAIN
value as a frame rate value (P) or gain value
(

:).

The DS.GAIN value is displayed
as a gain value (

:).

FRM RATE: The DS.GAIN value is displayed

as a frame rate value (P).

TABLE

A
B

For selecting the VF MARKER setting table.
This item is used to set the current values of
table A or B which have been selected using
the menu items listed below.

CENTER MARK

OFF
1
2
3
4

For selecting the center marker.
OFF: The center marker is not displayed.
1:

+ (large)

Center blank (large)

+ (small)

Center blank (small)

SAFETY ZONE

OFF
1
2

For selecting the type of safety zone frame.
OFF: The safety zone frame is not displayed.
1:

Box

Corner frames

SAFETY AREA

80%

:

90%

:

100%

For setting the position of the safety zone.

FRAME SIG

4:3
13:9
14:9
VISTA

For setting the frame marker.
The VISTA setting is 16:8.65.

FRAME MARK

ON
OFF

For selecting ON or OFF for the frame
marker.

FRAME LVL

00

:

15

For setting the level outside the frame marker.
0:

Equivalent to signal OFF

15: Same brightness as center area

However, this setting has no effect if
FRAME SIG is set to VISTA.

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

C U F E

SPOT

OFF

ON

109%

0%

01.AJ-HDX400E(VQT0P57)E  05.1.20  15:50  ページ85