Panasonic AJ-HDX900 Benutzerhandbuch
89
5
Chapter 5 Preparation
(continued)
5-10 Connection of the remote
control unit (AJ-RC10G)
It is possible to control some of the functions remotely by
connecting the remote control unit AJ-RC10G (optional
accessory).
When AJ-RC10G is connected to the REMOTE connector on
the unit and the power switches of both of the unit and AJ-
RC10G are turned on, the unit automatically enters the
remote control mode.
The remote control mode is released when AJ-RC10G is
removed or the power for the AJ-RC10G is turned OFF.
connecting the remote control unit AJ-RC10G (optional
accessory).
When AJ-RC10G is connected to the REMOTE connector on
the unit and the power switches of both of the unit and AJ-
RC10G are turned on, the unit automatically enters the
remote control mode.
The remote control mode is released when AJ-RC10G is
removed or the power for the AJ-RC10G is turned OFF.
Switch functions in the remote control mode
In the remote control mode, the following switches and
buttons on the unit are disabled.
buttons on the unit are disabled.
O
SHUTTER switch
O
MENU button
O
JOG dial button
O
GAIN switch
O
OUTPUT/AUTO KNEE switch
O
WHITE BAL switch
O
USER MAIN button (when operations other than VTR
operations are allocated)
operations are allocated)
O
USER 1 button (when operations other than VTR
operations are allocated)
operations are allocated)
O
USER 2 button (when operations other than VTR
operations are allocated)
operations are allocated)
VTR operations in the remote control mode
In the remote control mode, the VTR can be operated with
either the unit or AJ-RC10G.
either the unit or AJ-RC10G.
<Notes>
O
The state that was adjusted by connecting AJ-RC10G is
stored in the unit. Not to store the adjusted state in the
unit, open the FUNCTION MENU of AJ-RC10G to set the
RC DATA SAVE item to “OFF”.
stored in the unit. Not to store the adjusted state in the
unit, open the FUNCTION MENU of AJ-RC10G to set the
RC DATA SAVE item to “OFF”.
O
When the dedicated cable is connected or removed,
ensure that the POWER switches on both the main unit
and AJ-RC10G are turned “OFF”.
ensure that the POWER switches on both the main unit
and AJ-RC10G are turned “OFF”.
1
2
3
4
5-11 Connection of the external
switch
It is possible to draw 1.5 A current from the DC OUT
connector of the unit.
REC start/stop can be controlled by connecting an external
switch to this connector.
Since a tally lamp can be used by connecting an LED to this
connector, it is useful for shooting video when fixing the
camera on a crane.
connector of the unit.
REC start/stop can be controlled by connecting an external
switch to this connector.
Since a tally lamp can be used by connecting an LED to this
connector, it is useful for shooting video when fixing the
camera on a crane.
1: GND
2: TALLY OUT
2: TALLY OUT
Open collector output on the unit side
TALLY ON: Low impedance
TALLY OFF: High impedance
TALLY ON: Low impedance
TALLY OFF: High impedance
3: REC start/stop switch
This is connected in parallel to the REC START button on the unit or the
VTR button on the lens
VTR button on the lens
4: +12V
Connector at the cable side
HR10A-7R-4P(73)
(Hirose Denki)
DC OUT connector
REC start/stop
LED
Resistance
Max. 50 mA
AJ-RC10G
REMOTE connector
Dedicated cable
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.22 12:53 PM ページ89