Panasonic PV-GS500 Benutzerhandbuch
Others
77
LSQT0975
2: The screen has changed suddenly.
• Has the demonstration started? In the Tape
• Has the demonstration started? In the Tape
Recording mode, if you set [DEMO MODE] >>
[ON] without inserting a cassette and a card,
the demonstration starts. For normal use, set
this function to [OFF]. (
[ON] without inserting a cassette and a card,
the demonstration starts. For normal use, set
this function to [OFF]. (
-71-
)
3: A cassette cannot be inserted.
• Has condensation occurred? Wait until the
• Has condensation occurred? Wait until the
condensation indication disappears.
4: Auto focus function does not work.
• Is manual focus mode selected? If auto focus
• Is manual focus mode selected? If auto focus
mode is selected, focus is automatically
adjusted.
adjusted.
• There are some recording subjects and
surroundings for which the auto focus does not
operate correctly. (
operate correctly. (
-84-
) If so, use the manual
focus mode to adjust the focus. (
-45-
)
• Is the MagicPix function set? When the
MagicPix function is working, focusing shifts
into the manual mode.
into the manual mode.
• Is the card slow shutter mode activated? In
card slow shutter mode, focusing shifts into the
manual mode.
manual mode.
5: The Camcorder arbitrarily stops recording.
• Is the AGS function activated? Record in the
• Is the AGS function activated? Record in the
normal horizontal position or set [AGS] to
[OFF].(
[OFF].(
-39-
)
Indications
1: A sentence is displayed in red in the screen
1: A sentence is displayed in red in the screen
center.
• Read the contents and respond to them. (
-73-
)
2: The time code becomes inaccurate.
0 The time code indication counter may not be
0 The time code indication counter may not be
constant in the reversed slow-motion playback,
but this is not a malfunction.
but this is not a malfunction.
3: The remaining tape time indication
disappears.
• The remaining tape time indication may
disappear temporarily during frame-by-frame
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
playback or other operation. If you continue
ordinary recording or playback, the indication is
restored.
4: The remaining tape time Indication does not
match the actual remaining tape time.
• If scenes of less than 15 seconds are
continuously recorded, the remaining tape time
cannot be correctly displayed.
cannot be correctly displayed.
• In some cases, the remaining tape time
indication may show remaining tape time that is
2 to 3 minutes shorter than the actual
remaining tape time.
2 to 3 minutes shorter than the actual
remaining tape time.
5: A function indication such as mode
indication, remaining tape time indication,
or time code indication is not shown.
or time code indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF],
indications other than the tape running
condition, warning, and date indications
disappear.
condition, warning, and date indications
disappear.
Playback (Sound)
1: Sound is not played back from the built-in
1: Sound is not played back from the built-in
speaker of the Camcorder.
0 Is the volume too low? During playback, push
the [
s
/VOL
r] lever to display the volume
indication and adjust it. (
-47-
)
2: Different sounds are reproduced at the
same time.
• Have you set [SETUP] >> [12bit AUDIO] >>
[MIX]? If you set [AUDIO REC] >> [12bit] and
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
dub audio to a recorded tape, you can hear the
sound on recording and the sound dubbed at a
later time. To hear the sounds separately, set
to [ST1] or [ST2]. (
-56-
)
• Have you set [SETUP] >> [AUDIO OUT] >>
[STEREO] and reproduced a picture containing
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (
the main sound and sub sound? Set to [L] to
hear main sound, and set to [R] to hear the sub
sound. (
-71-
)
3: Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on
• Is the accidental erasure prevention slider on
the cassette open? If it is open (set to [SAVE]),
audio dubbing cannot be performed. (
audio dubbing cannot be performed. (
-21-
)
• Are you attempting to edit a tape portion that
was recorded in LP mode? LP mode does not
allow audio dubbing. (
allow audio dubbing. (
-30-
)
4: The original sound was erased when audio
dubbing was performed.
• If you perform audio dubbing on a recording made
in [16bit] mode, the original sound will be erased.
If you wish to preserve the original sound, be sure
to select [12bit] mode when recording.
If you wish to preserve the original sound, be sure
to select [12bit] mode when recording.
5: Sounds cannot be played back.
• Although a cassette with no audio dubbing is
• Although a cassette with no audio dubbing is
being played, have you set [SETUP] >>
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1]. (
[12bit AUDIO] >> [ST2]? To play back a
cassette with no audio dubbing, set
[12bit AUDIO] >> [ST1]. (
-56-
)
• Is the variable speed search function working?
Press the [VAR SEARCH] button on the
remote control to cancel the variable speed
search function. (
remote control to cancel the variable speed
search function. (
-48-
)
LSQT0975_ENG.book 77 ページ ２００５年１２月１９日 月曜日 午前９時５１分